Yaesu
[Top] [All Lists]

Re: [Yaesu] Yaesu Digest, Vol 81, Issue 6 - translated

To: <yaesu@contesting.com>
Subject: Re: [Yaesu] Yaesu Digest, Vol 81, Issue 6 - translated
From: <kq6i@arrl.net>
Date: Sun, 13 Sep 2009 16:05:17 -0600
List-post: <yaesu@contesting.com">mailto:yaesu@contesting.com>
 the yaesu gentlemen I am interested in obtaining a yaesu line diagrams but but 
may I them estare typing when I needed to
say that when a colleague bring me your radio to repair I keep the diagramo or 
manual thank estare in contact with you.
Carlos peña (j) adolfo

-----Original Message-----
From: Carlos Adolfo Peña [mailto:carlosadolfopjm@hotmail.com] 
Sent: Sunday, September 13, 2009 3:16 PM
To: c......yaesu
Subject: Re: [Yaesu] Yaesu Digest, Vol 81, Issue 6


señores de la yaesu estoy interesado en obtener unos diagramas de la linea 
yaesu pero sino es posible yo les estare
escribiendo cuando yo los necesite quiero decir que cuando un colega me traiga 
su radio para reparar yo tenga el diagramo o
manual muchas gracias estare en contacto con ustedes.

carlos adolfo peña j

colombia s.a

> From: yaesu-request@contesting.com
> Subject: Yaesu Digest, Vol 81, Issue 6
> To: yaesu@contesting.com
> Date: Sun, 13 Sep 2009 12:00:42 -0700
> 
> Send Yaesu mailing list submissions to
> yaesu@contesting.com
> 
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.contesting.com/mailman/listinfo/yaesu
> or, via email, send a message with subject or body 'help' to
> yaesu-request@contesting.com
> 
> You can reach the person managing the list at
> yaesu-owner@contesting.com
> 
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Yaesu digest..."
> 
> 
> Today's Topics:
> 
> 1. G-1000 DXA calibration (Mike)
> 
> 
> ----------------------------------------------------------------------
> 
> Message: 1
> Date: Sat, 12 Sep 2009 18:57:33 -0400
> From: Mike <nf4l_NO_SPAM@nf4l.com>
> Subject: [Yaesu] G-1000 DXA calibration
> To: Yaesu Reflector <yaesu@contesting.com>
> Message-ID: <4AAC275D.70303@nf4l.com>
> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
> 
> On page 8 of the manual, in item 7, there is mention of two raised 
> calibration marks. My rotor has three, the one on the base and two on 
> the rotating bell. The two on the rotating bell are roughly 90 degrees 
> apart. One is above the mold mark (or separation) and one is below.
> 
> Which one is the correct one to use for the alignment procedure? Neither 
> is aligned with the mark on the base.
> 
> 73, Mike NF4L
> 
> 
> ------------------------------
> 
> _______________________________________________
> Yaesu mailing list
> Yaesu@contesting.com
> http://lists.contesting.com/mailman/listinfo/yaesu
> 
> 
> End of Yaesu Digest, Vol 81, Issue 6
> ************************************

_________________________________________________________________
Explore the seven wonders of the world
http://search.msn.com/results.aspx?q=7+wonders+world&mkt=en-US&form=QBRE
_______________________________________________
Yaesu mailing list
Yaesu@contesting.com
http://lists.contesting.com/mailman/listinfo/yaesu

_______________________________________________
Yaesu mailing list
Yaesu@contesting.com
http://lists.contesting.com/mailman/listinfo/yaesu

<Prev in Thread] Current Thread [Next in Thread>