Hanging in transmit, particularly with the K3, seems to be related
to using both radio command for PTT and hardware PTT. Make sure you
Set "Comm PTT" to "NO" for each radio.
I've seen reports of the problem with other radios but it is most common
in the K3. I've also seen reports of the problem with other
software/logging programs and with other interfaces - even basic
serial cables and simple transistor PTT/FSK drivers.
73,
... Joe, W4TV
On 9/26/2010 10:14 PM, Bruce Meier wrote:
> Alan,
>
> I have (2) K3s, WriteLog, and audio fed through the sound card and a DX
> Doubler. When SSB only (no DVK) the audio is fine in K3 Vox mode. However,
> when using the DVK and K3 VOX, (sound card DVK / WriteLog / WinXP) the K3s
> (both of them) hang in XMIT until I push escape......sometimes!!! The only
> way I have been able to get around it is to use PTT when using the DVK.
>
> All 'on the fly' recording works fine - if in PTT. If in VOX, I can't
> always get the recording to stop fast enough. Why..... it hangs in XMIT.
> So, when I want to record on the fly, I turn off VOX. By pushing Shift-fn
> (what ever key) PTT is asserted by the PC and all is well and escape
> immediately stops the recording.
>
> I think this is something K3 related as the exact same configuration worked
> with my FT1000-MPs. NO HANGING !!
>
> 73,
> Bruce - N1LN
>
>
>
> -----Original Message-----
> From: writelog-bounces@contesting.com
> [mailto:writelog-bounces@contesting.com] On Behalf Of Alan Maenchen
> Sent: Sunday, September 26, 2010 22:05
> To: writelog@contesting.com
> Subject: [WriteLog] setup issue with microHAM
>
> This is getting fustrating. I'm using WL 10.77H
> Rig is K3 plus the microHAM MK2R+ (with router 7.7.1). Computer is an XP
> laptop.
>
> SSB audio works fine .. manually. Mic is looped through the MK2R+ sound
> card function. SB setup has both the recording loop and echo microphone
> checked.
> I'm using the MK2R+ box for the CW keyer and sound card functions .. but
> just for one radio.
>
> Problem 1: Playing a recorded SSB message works fine until the end. At the
> end, rig control does not switch back to RX. However, the TX LED on the
> microHAM box turns off properly. Yet, the radio stays in TX mode until I
> hit the ESC key. Also, in Windows audio, the Mic is muted during actual wave
> file playing, then unmutes correctly at the end. It's just the radio that
> gets stuck in TX.
>
> Problem 2: Recording an SSB message fails. Audio level is zero on record as
> if the mic is muted. However, playing an old message (made>year ago) works
> OK. Or playing a message recorded outside of Writelog works OK too (except
> for problem 1 above). WlogSbControl shows "USB Voice CODEC" in all areas,
> which is correct. However, the Mic level bar is grayed out, but checked as
> "active".
>
> This has to be some dumb setup issue. I dont do SSB very often, but every
> time I do this it's a real headache. Presently have the normal station
> disrupted and I'm setting up a portable station for use in CQP next weekend.
>
>
> TIA& 73, Alan AD6E K6K/40
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|