Hi, Joe,
I have a PK-900
There is no such entry in my writelog.ini file of
COM1:=9600,n,8,1,x
What I see is this:
[Rttyrite2]
Port=1 WHAT PORT IS THIS COM 1??
Speed=0 WHAT SPEED IS THIS 45baud
Type=2 WHAT TYPE TNC I ASSUME A PK-232
What I would really like is the FILE that sets the init commands
for the RTTY window for a PK-232
But if your suggestion will work great...
BUT why no information as you said in my writelog.ini???
KR4DA wrote:
> Try this
>
>PK-232 INTERFACING
>If WriteLog will
>not communicate with your PK-232, it may be necessary to do the
>editing described below.
>Using NotePad edit C:\Windows\writelog.ini as follows:
>In the file, go to the section labeled [Ports].
>Look at the line for the Com port you intend to use. It will look like
>this:
>COM1:=9600,n,8,1,x
>Check to be sure all parameters are correct, then Delete the final x
>(but not
>the comma). It should look like this:
>COM1:=9600,n,8,1,
>Click on File, Save. Then open WriteLog; this should allow
>your PK-232 to communicate with WriteLog.
>
>Also there is a undocumented commant to see the mode on the PK-232 and
>maybe should work with the PK-900.
>
>Look below. The command TncInit1 with set the mode of the TNC to any
>mode you want. The default in Writelog is RTTY. In the example below,
>The TncInit1=MO sets the PK-232 to Morsecode instead of rtty on
>startup. The 2nd command TncInit2= Is any other command you might want
>on startup. I did not need anything else but the MO(orse) command so I
>commented out the 2nd command with the ";".
>
>I think most of your problem will be solve with the comport modification
>as above. I think I was probably the only one that every used the
>TncInit command.
>
>Rttyrite]
>FontHeight=23
>Port=2
>Speed=0
>diddle=1
>Type=15
>TncInit1=MO
>;TncInit2=
>
>
>Joe K0BX
>
>KR4DA wrote:
>
>> Where are the INIT strings for the PK232 located..
>> I want to modifiy them...
>>
>> OK I got it going again.....
>> I got the PK900 command set book out...
>> I only set the options that would allow the PK900
>> to work as ONE RADIO PORT 1 and RTTY set
>> for PORT 1 options...
>> Now it is initing ok ....
>>
>>
>> KR4DA wrote:
>>
>>
>>>Well what happended???????????????????
>>>I went and started the program again and the error is
>>>RTTY window when clicking PK232 says.........
>>>INIT HOST MODE pls wait.....
>>>
>>>Then PK232 init failed try again.....
>>>
>>>I have gone over and over it.. I had it working now it won't
>>>
>>>I can EXIT writelog then
>>>talk to the PK900 with HYPER term dumb terminal pgm and the other pgms
>>>I have...
>>>
>>>
>>
>>
>
>--
>Stop the insanity!
>Please do not add me to any distribution lists (Joke, Stories or Junk)
>without my permission.
>
>_______________________________________________
>WriteLog mailing list
>WriteLog@contesting.com
>http://lists.contesting.com/mailman/listinfo/writelog
>WriteLog on the web: http://www.writelog.com/
>
>
>
>
>
>--
>Bob
>Vmoa chat list -> http://autos.groups.yahoo.com/group/vmoachat/
>Vmoa tech list home -> http://autos.groups.yahoo.com/group/vmoatech/
>
>
>Middleburg Fl (South Jacksonville)
>ICQ 13912841
>Web Page http://bellsouthpwp.net/k/r/kr4da
>
>Visit the FDXPG at http://www.geocities.com/w4wx1/
>
>Ham Radio Calls: KR4DA FG/KR4DA J79DA HK0/KR4DA
>
>Motorcycles CBMMA #4
>1977 XS750D 1J7008405
>1997 Vmax12J VMOA #504
>
--
de KR4DA Bob Middleburg, FL
HK0/KR4DA J79DA FG/KR4DA
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|