One other thing I noticed. The CW Receive Speed is not displayed when using
the CW Decoder, or am I missing it. The Transmit speed is displayed, but not
receive.
> -----Original Message-----
> From: writelog-admin@contesting.com
> [mailto:writelog-admin@contesting.com]On Behalf Of GilBaronW0MN
> Sent: Wednesday, December 12, 2001 11:19
> To: scot@k9jy.com; Writelog
> Subject: RE: [WriteLog] Noise in sound
>
>
>
>
> > -----Original Message-----
> > From: writelog-admin@contesting.com
> > [mailto:writelog-admin@contesting.com]On Behalf Of Scot Herrick
> > Sent: Wednesday, December 12, 2001 10:35
> > To: Writelog; GilBaronW0MN
> > Subject: RE: [WriteLog] Noise in sound
> >
> >
> > Hi Gil,
> >
> > Try closing the Rttyrite window and use the CW Decoder instead
> found under
>
>
> Thanks for the reply. You have given me a work around that is
> satisfactory.
> Yes that works although I like the Rttyrite window better. It
> confirms that
> there is a problem with it so I will have to use the CW Decoder.
>
> I did have all else muted, except Wav Level of course which cannot be.
>
> > 'Windows' on the Toolbar. It will decode your CW just fine and
> on multiple
> > channels and might take care of the noise you are hearing.
> >
> > Also, open your native volume controls on your PC and mute
> > everything except
> > 'Volume.' Sometimes you will pick up noise using the sound card from the
> > 'CD' channel or others because it's not muted.
> >
> > CU...Scot, K9JY
> >
> > K9JY's WriteLog User Support Site at:
> > http://www.k9jy.com
> > mailto:scot@k9jy.com
> >
> >
> > > -----Original Message-----
> > > From: writelog-admin@contesting.com
> > > [mailto:writelog-admin@contesting.com]On Behalf Of GilBaronW0MN
> > > Sent: Wednesday, December 12, 2001 02:54 PM
> > > To: Writelog@Contesting. Com
> > > Subject: [WriteLog] Noise in sound
> > >
> > >
> > > I was setting up for the 10 meter contest which is both CW and
> > > SSB and have
> > > discovered a problem that makes it very difficult to use sound.
> > > If the Rttyrite window is open then there is a T of noise in the
> > > output of a
> > > wave file that was previously recorded with no noise. If I shut
> > > the Rttyrite
> > > window then it is quiet. This means that I have to set up for
> > CW if I want
> > > the CW decoding every tie I switch from SSB to CW and close and
> > > readjust the
> > > SSB windows when switching from CW to SSB.
> > >
> > > Has anyone noticed this problem and found a solution. I tried
> > > over and over
> > > with various configurations and cannot get rid of the noise.
> > >
> > > Gil Baron http://webpages.charter.net/gbaron
> > > 44:04.925 N 92:30.758 W 1055'
> > > "Hierro candente, batir de repente"
> > >
> > > _______________________________________________
> > > WriteLog mailing list
> > > WriteLog@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/writelog
> >
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/writelog
> >
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
>
|