You seem to have the two setup pre-requisites right: each
Entry window must have an "L" and an "R" display, and,
if you're running the RTTY window, it must be setup for
one of the two stereo settings (FSK or AFSK). With those
two setup items correct, I don't see how WL could confuse
the L/R channels.
How are you starting up the L/R RTTY windows? You have
to start them one at a time from within WL, once after
setting the focus to each radio.
I suggest going to Tools Soundboard Options, and turn
ON the "Continuously Record" button, and click OK.
Make sure there's a different signal on the L and
R radios, and then turn the recoding back OFF.
Then bring up the WL "AudioReview" program. The file
you just made should already be in the "wave files
recorded" window. So select it and click the Play
button. Do you get the different signals in the
L and R channels?
Wayne
> -----Original Message-----
> From: owner-writelog@contesting.com
> [mailto:owner-writelog@contesting.com]On Behalf Of Dick Green
> Sent: Sunday, March 11, 2001 19:03
> To: WriteLog; Ric Plummer
> Subject: RE: [WriteLog] WL soundboard channel problem
>
>
>
> Yeah, I have it set up correctly. It's just that WL does not
> select the R
> channel when I select the R entry window. Again, it's not the
> soundcard -- I
> can see the two different signals that are on the two
> channels when I look
> at the VU meters in the Recording Control window. You can display this
> windows by doing the following:
>
> 1. Double-click on the speaker icon in the tray to bring up
> the full Volume
> Control window.
> 2. Pull down the Options menu and select Properties. This
> will display the
> Properties window.
> 3. Click the second radio button down -- "Recording" and Click OK. The
> Recorning Control Window will be displayed.
>
> This feature could be dependent on the drivers that run your
> soundcard. I
> think the driver has to have mixer software. In mine, the
> mixer pull-down
> list in the Properties window says, "DS-XG Mixer". I'm using a Dell
> Dimension XPS with a Yamaha soundboard.
>
> I'll ask again: Does anybody have a clue why WL can't select
> the R channel
> in my system? Wayne?
>
> 73, Dick WC1M
>
> > -----Original Message-----
> > From: Ric Plummer [mailto:ric@kv1w.com]
> > Sent: Friday, March 09, 2001 7:55 AM
> > To: dick.green@valley.net
> > Subject: Re: [WriteLog] WL soundboard channel problem
> >
> >
> > Dick,
> > I assume you have two entry screens.
> > And did you do the routine of select one entry the go to radio and
> > select this is right radio AND the click on activate this radio
> > and then go to the other and do the left routine ? ( both parts ).
> > This is where I tripped up at times.
> > Also, what sound control are you using that has a "meter" ?
> > I had one once, don't know where it came from or went to,
> but no longer.
> > I have W2K and oth wondoz ones as well as Creative, but no
> "VU Meter"
> > Ric KV1W
> >
> > ----- Original Message -----
> > From: "Dick Green" <dick.green@valley.net>
> > To: "WriteLog" <Writelog@contesting.com>
> > Sent: Friday, March 09, 2001 06:43
> > Subject: [WriteLog] WL soundboard channel problem
> >
> >
> > >
> > > I've used WL for RTTY/PSK with one radio for a while and
> now I'm setting
> > it
> > > up for two radios. No matter what I do, WL always selects audio
> > input from
> > > the Left channel of the soundboard's line input. It does this
> > whether the
> > > Left or Right entry window is selected.
> > >
> > > The soundboard checker gives my soundboard a 7f, the
> highest rating. I
> > think
> > > all the hardware is setup correctly and all obvious
> parameters in WL are
> > set
> > > correctly (the TU-Type is set to "Stereo Board AFSK".) I
> connected the
> > > line-level audio output from each rig to one of the two
> channels on the
> > > stereo line input connector. If I display the Windows
> Record Control, I
> > can
> > > see that the soundboard is receiving audio from each rig
> on the correct
> > > channel (if I push the balance slider either to the Left
> or Right, the
> > level
> > > meter tracks the corresonding rig.) Therefore, I have to
> > conclude that the
> > > soundboard is working properly. But WL always selects the Left
> > channel and
> > > never selects the Right channel.
> > >
> > > Am I doing something wrong here? Is there a magic .ini
> > parameter I need to
> > > set?
> > >
> > > 73, Dick WC1M
> > >
> > >
> > >
> > >
> > > --
> > > WWW: http://www.writelog.com/
> > > Submissions: writelog@contesting.com
> > > Administrative requests: writelog-REQUEST@contesting.com
> > > Problems: owner-writelog@contesting.com
> > >
> > >
> >
>
>
> --
> WWW: http://www.writelog.com/
> Submissions: writelog@contesting.com
> Administrative requests: writelog-REQUEST@contesting.com
> Problems: owner-writelog@contesting.com
>
>
--
WWW: http://www.writelog.com/
Submissions: writelog@contesting.com
Administrative requests: writelog-REQUEST@contesting.com
Problems: owner-writelog@contesting.com
|