Yeah, I have it set up correctly. It's just that WL does not select the R
channel when I select the R entry window. Again, it's not the soundcard -- I
can see the two different signals that are on the two channels when I look
at the VU meters in the Recording Control window. You can display this
windows by doing the following:
1. Double-click on the speaker icon in the tray to bring up the full Volume
Control window.
2. Pull down the Options menu and select Properties. This will display the
Properties window.
3. Click the second radio button down -- "Recording" and Click OK. The
Recorning Control Window will be displayed.
This feature could be dependent on the drivers that run your soundcard. I
think the driver has to have mixer software. In mine, the mixer pull-down
list in the Properties window says, "DS-XG Mixer". I'm using a Dell
Dimension XPS with a Yamaha soundboard.
I'll ask again: Does anybody have a clue why WL can't select the R channel
in my system? Wayne?
73, Dick WC1M
> -----Original Message-----
> From: Ric Plummer [mailto:ric@kv1w.com]
> Sent: Friday, March 09, 2001 7:55 AM
> To: dick.green@valley.net
> Subject: Re: [WriteLog] WL soundboard channel problem
>
>
> Dick,
> I assume you have two entry screens.
> And did you do the routine of select one entry the go to radio and
> select this is right radio AND the click on activate this radio
> and then go to the other and do the left routine ? ( both parts ).
> This is where I tripped up at times.
> Also, what sound control are you using that has a "meter" ?
> I had one once, don't know where it came from or went to, but no longer.
> I have W2K and oth wondoz ones as well as Creative, but no "VU Meter"
> Ric KV1W
>
> ----- Original Message -----
> From: "Dick Green" <dick.green@valley.net>
> To: "WriteLog" <Writelog@contesting.com>
> Sent: Friday, March 09, 2001 06:43
> Subject: [WriteLog] WL soundboard channel problem
>
>
> >
> > I've used WL for RTTY/PSK with one radio for a while and now I'm setting
> it
> > up for two radios. No matter what I do, WL always selects audio
> input from
> > the Left channel of the soundboard's line input. It does this
> whether the
> > Left or Right entry window is selected.
> >
> > The soundboard checker gives my soundboard a 7f, the highest rating. I
> think
> > all the hardware is setup correctly and all obvious parameters in WL are
> set
> > correctly (the TU-Type is set to "Stereo Board AFSK".) I connected the
> > line-level audio output from each rig to one of the two channels on the
> > stereo line input connector. If I display the Windows Record Control, I
> can
> > see that the soundboard is receiving audio from each rig on the correct
> > channel (if I push the balance slider either to the Left or Right, the
> level
> > meter tracks the corresonding rig.) Therefore, I have to
> conclude that the
> > soundboard is working properly. But WL always selects the Left
> channel and
> > never selects the Right channel.
> >
> > Am I doing something wrong here? Is there a magic .ini
> parameter I need to
> > set?
> >
> > 73, Dick WC1M
> >
> >
> >
> >
> > --
> > WWW: http://www.writelog.com/
> > Submissions: writelog@contesting.com
> > Administrative requests: writelog-REQUEST@contesting.com
> > Problems: owner-writelog@contesting.com
> >
> >
>
--
WWW: http://www.writelog.com/
Submissions: writelog@contesting.com
Administrative requests: writelog-REQUEST@contesting.com
Problems: owner-writelog@contesting.com
|