VHFcontesting
[Top] [All Lists]

Re: [VHFcontesting] [NEWSVHF] 222 Sprint

To: "paul@n1bug.com" <paul@n1bug.com>, "newsvhf@mailman.qth.net" <newsvhf@mailman.qth.net>, "vhfcontesting@contesting.com" <vhfcontesting@contesting.com>
Subject: Re: [VHFcontesting] [NEWSVHF] 222 Sprint
From: mike repinski via VHFcontesting <vhfcontesting@contesting.com>
Reply-to: mikflathead@aol.com
Date: Wed, 28 Sep 2022 14:33:10 +0000 (UTC)
List-post: <mailto:vhfcontesting@contesting.com>
Does the rope just lay in the elements? Mike


-----Original Message-----
From: Paul N1BUG FN55mf <paul@n1bug.com>
To: NEWSVHF@mailman.qth.net <newsvhf@mailman.qth.net>; 
vhfcontesting@contesting.com <vhfcontesting@contesting.com>
Sent: Wed, Sep 28, 2022 5:21 am
Subject: Re: [VHFcontesting] [NEWSVHF] 222 Sprint

Conditions were extremely variable! I got 13 QSOs in 9 grids, all 
SSB/CW. Not too bad considering where I'm located but it sure gets slow 
after the first hour.

At the start everyone was weak! I had to resort to CW to work N1JEZ and 
K1TEO! Then I got N2SLN in FN22 on SSB with a good signal, somewhat 
surprising considering that WSW direction has always been hard from here.

Around 0100 someone found the propagation switch and moved it to the ON 
position. I heard K1PXE calling on SSB. Pete was 55 which may be the 
strongest I've ever heard him but he quickly faded. We switched to CW, 
easily completing the QSO. Pete was peaking close to S5 again at the 
end. A moment later K1TEO was up to S9+. What a change from an hour earlier!

Best distance was N2JMH at 470 miles on SSB with a great signal. I 
copied a few good solid CW transmissions from W1XR at 560 miles but Jim 
couldn't hear me.

Some "easy" ones were missed because I never heard them calling in this 
direction. That's normal.

There was a bunch of us waiting for K1DY like cats by a mouse hole! I 
didn't hang around long after working Bill as I hadn't had any other 
QSOs in over an hour and I needed more sleep. I hope he had fun working 
the gang.

I managed to get the clump of dirt and vegetation debris out of the 6 
meter driven element and rope run through three elements yesterday. I 
came in to take a break and fell asleep, so still have four elements to 
do. I am able to pull the 1/4" rope through where there is only a 3/16" 
gap on either side of the U bolts holding the element to the boom by 
running a stiff wire through the element, tapering the end of the rope 
and taping it to the wire. It took some trial and error to figure out 
how to tape it so it stays on but will still squeeze through. This is 
one application where the ultra-cheap ultra-thin vinyl tape actually 
works better than the good stuff! The ropes are wedged in pretty tight 
at the center of the elements and shouldn't move. That's good because I 
am thinking about not capping the ends of the elements. They have never 
been capped before. I know water gets in around the U bolt and if it 
can't run out the end I could have elements filling with water.

73,
Paul N1BUG
FN55mf
_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting
_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting

<Prev in Thread] Current Thread [Next in Thread>