Re: [TowerTalk] Masting source

[K9MA <k9ma@sdellington.us>]

That's interesting. DXE did not have the 11 foot version available last 
spring when I rebuilt my antenna system. I ordered the 10 ft. Rohn mast 
from Texas Towers, which was adequate for my needs. It also shipped with 
the tower, so added little to shipping cost.
73,
Scott K9MA

On 12/29/2019 20:38, Tim Duffy wrote:
> DX Engineering has several high quality masts.
>
> 11 feet and 22 feet long - Chrome-moly - hot dipped galvanized - pretty low 
> truck shipping rates
>
> https://www.dxengineering.com/parts/dxe-st200cm-11
>
> https://www.dxengineering.com/parts/dxe-st200cm-22
>
> 73
> Tim K3LR
> @ DX Engineering
>
>
>
>
>
> -----Original Message-----
> From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Gene 
> Smar via TowerTalk
> Sent: Saturday, December 28, 2019 4:23 PM
> To: 'towertalk reflector'
> Subject: Re: [TowerTalk] Masting source
>
> Rob:
>
>       I ordered my mast from Special Metals, Inc., Joe Varva (1-800-727-7177).  
> This was back in 2001 so Joe may no longer work there but it's worth a try.  My 
> mast arrived within a week of my order, IIRC.
>
>
> 73 de
> Gene Smar  AD3F
>
>
>
> -----Original Message-----
> From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Jeffrey 
> Okamitsu
> Sent: Saturday, December 28, 2019 12:39 PM
> To: K9MA <k9ma@sdellington.us>
> Cc: towertalk@contesting.com
> Subject: Re: [TowerTalk] Masting source
>
> Try onlinemetals.com
>
> 73. Jeff
> W3KL
>
> Sent from my iPhone
>
> > On Dec 28, 2019, at 12:34 PM, K9MA <k9ma@sdellington.us> wrote:
> >
> > Bob,
> >
> > Are you putting the rotator in the tower with a thrust bearing or sleeve?
> >
> > 73,
> > Scott K9MA
> >
> > > On 12/28/2019 10:39, Dave Hachadorian wrote:
> > > I bought a 10-footer once from Texas Towers.  They cut 1 foot off to make it 
> > > UPS shippable.  That was a long time ago though.
> > >
> > > Dave Hachadorian, K6LL
> > > Yuma, AZ
> > >
> > >
> > > -----Original Message----- From: Rob Matherly
> > > Sent: Saturday, December 28, 2019 9:26 AM
> > > To: TowerTalk@contesting.com
> > > Subject: [TowerTalk] Masting source
> > >
> > > Hi All -
> > >
> > > Could someone point me to a source for antenna mast? It needs to be
> > > strong enough for my A4S and 10-element 2m beam. I was thinking 10'
> > > in height, is that too much? I've not had an actual bell rotor atop a tower 
> > > before.
> > > Everything prior has been TV rotors on masts.
> > >
> > > Thanks!
> > >
> > > Rob Matherly, W0JRM
> > > Centerville, Iowa - EN30nr
> > > SKCC 29, FISTS 19246
> > >
> > > "Aude, vide, tace, si vis vivere in pace."
> > > _______________________________________________
> > >
> > >
> > >
> > > _______________________________________________
> > > TowerTalk mailing list
> > > TowerTalk@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/towertalk
> > > _______________________________________________
> > >
> > >
> > >
> > > _______________________________________________
> > > TowerTalk mailing list
> > > TowerTalk@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/towertalk
> > --
> > Scott  K9MA
> >
> > k9ma@sdellington.us
> >
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
--
Scott  K9MA

k9ma@sdellington.us

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk