Towertalk
[Top] [All Lists]

Re: [TowerTalk] Masting source

To: "'Gene Smar'" <ersmar@verizon.net>, <TowerTalk@contesting.com>
Subject: Re: [TowerTalk] Masting source
From: "Tim Duffy" <k3lr@k3lr.com>
Date: Sun, 29 Dec 2019 21:38:22 -0500
List-post: <mailto:towertalk@contesting.com>
DX Engineering has several high quality masts.

11 feet and 22 feet long - Chrome-moly - hot dipped galvanized - pretty low 
truck shipping rates

https://www.dxengineering.com/parts/dxe-st200cm-11

https://www.dxengineering.com/parts/dxe-st200cm-22

73
Tim K3LR
@ DX Engineering





-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Gene 
Smar via TowerTalk
Sent: Saturday, December 28, 2019 4:23 PM
To: 'towertalk reflector'
Subject: Re: [TowerTalk] Masting source

Rob:

     I ordered my mast from Special Metals, Inc., Joe Varva (1-800-727-7177).  
This was back in 2001 so Joe may no longer work there but it's worth a try.  My 
mast arrived within a week of my order, IIRC.


73 de
Gene Smar  AD3F



-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Jeffrey 
Okamitsu
Sent: Saturday, December 28, 2019 12:39 PM
To: K9MA <k9ma@sdellington.us>
Cc: towertalk@contesting.com
Subject: Re: [TowerTalk] Masting source

Try onlinemetals.com

73. Jeff
W3KL

Sent from my iPhone

> On Dec 28, 2019, at 12:34 PM, K9MA <k9ma@sdellington.us> wrote:
> 
> Bob,
> 
> Are you putting the rotator in the tower with a thrust bearing or sleeve?
> 
> 73,
> Scott K9MA
> 
>> On 12/28/2019 10:39, Dave Hachadorian wrote:
>> I bought a 10-footer once from Texas Towers.  They cut 1 foot off to make it 
>> UPS shippable.  That was a long time ago though.
>> 
>> Dave Hachadorian, K6LL
>> Yuma, AZ
>> 
>> 
>> -----Original Message----- From: Rob Matherly
>> Sent: Saturday, December 28, 2019 9:26 AM
>> To: TowerTalk@contesting.com
>> Subject: [TowerTalk] Masting source
>> 
>> Hi All -
>> 
>> Could someone point me to a source for antenna mast? It needs to be 
>> strong enough for my A4S and 10-element 2m beam. I was thinking 10' 
>> in height, is that too much? I've not had an actual bell rotor atop a tower 
>> before.
>> Everything prior has been TV rotors on masts.
>> 
>> Thanks!
>> 
>> Rob Matherly, W0JRM
>> Centerville, Iowa - EN30nr
>> SKCC 29, FISTS 19246
>> 
>> "Aude, vide, tace, si vis vivere in pace."
>> _______________________________________________
>> 
>> 
>> 
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>> _______________________________________________
>> 
>> 
>> 
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
> 
> 
> --
> Scott  K9MA
> 
> k9ma@sdellington.us
> 
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>