There's a photo on bottom of my home page (aa1k.us) showing several of the
bent pin shackles in place on my towers, and it links to another page with
some closeup photos. These are very useful hardware.
73/Jon
Jon P. Zaimes, AA1K
Tower climber for hire
http://www.aa1k.us/
Cell: 302-632-2353
Reviews of AA1K tower work on eham website:
http://www.eham.net/reviews/detail/12922
Hug your favorite tower every day, and always stay connected to it.
-----Original Message-----
From: TowerTalk <towertalk-bounces@contesting.com> On Behalf Of
al.n6ta@gmail.com
Sent: Wednesday, October 2, 2019 10:54 PM
To: 'Tim Duffy' <k3lr@k3lr.com>; 'Steve Maki' <lists@oakcom.org>;
'towertalk' <towertalk@contesting.com>
Subject: Re: [TowerTalk] EHS leads for Phillystran
How is the shackle to the tower connected to the insulator? I may want to
add some to my top guys.
Tnx.
Al
N6TA
-----Original Message-----
From: TowerTalk <towertalk-bounces@contesting.com> On Behalf Of Tim Duffy
Sent: Wednesday, October 02, 2019 7:20 PM
To: 'Steve Maki' <lists@oakcom.org>; 'towertalk' <towertalk@contesting.com>
Subject: Re: [TowerTalk] EHS leads for Phillystran
The problem with Preform connections is much worse as you go higher in
frequency.
I only had a photo of the 40 meter install.
Knowing what I know now I would never direct connect a Preform to the tower.
73
Tim K3LR
-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Steve
Maki
Sent: Wednesday, October 2, 2019 9:20 PM
To: towertalk
Subject: Re: [TowerTalk] EHS leads for Phillystran
It *disconnects* the preforms from the tower legs.
I must say I'm surprised that this action was needed when talking about
40 meters, but if one wants perfection, and sees SWR changes with antenna
rotation, then it's needed, no doubt about it.
-Steve K8LX
On 10/02/19 20:42 PM, Keith Dutson wrote:
> So this arrangement moves the preform away from the tower leg? I am
> rebuilding my tower and have three TIC rings mounted about 4 feet
> above
the
> guy mounts.
> I had a problem with just Preforms attaching to the tower legs
> connection
-
> which caused distortion in the pattern of close mounted Yagi's. That
> is, Yagi's that were mounted only a few feet above a guy connection
> point. The VSWR of the affected Yagi would change with rotation and
> the effect of
three
> Preforms connected to the tower was confirmed with modeling. The
> solution was to use a bent pin shackle and an insulator right at the
> tower connection. You can see it in this view of the middle four
> element 40
meter
> OWA Yagi stack at K3LR:
> http://www.k3lr.com/2016/ring.jpg
>
> Using insulators at the tower connection completely solved the pattern
> distortion and VSWR changes with rotation.
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|
