Well, OK you got me redesigning my little project. Don't know yet how I will
change it or just start over again. I do have the 1.50" X 0.120 heavy wall also
6' long. And I am considering how I could utilize some coils and/or capacitance
hat arrangements to shorten up the antenna. Closer to what I suppose a shorty
forty or something like that. One problem is I just haven't been up close to a
40 meter beam to get a decent idea what I am really dealing with. I know when I
tried to raise this one above my head probably a good 1/4 to 1/3 of the outer
elements were still on the ground. That before any kind of serious trussing.
Might even go back to the design like in QST antenna issue a couple years ago
with weighted wires hanging off the ends. But I would prefer something more
stable than that.
Terry
KI7M
> On August 14, 2018 at 9:54 PM Grant Saviers <grants2@pacbell.net> wrote:
>
>
> I second the "too small" opinion.
>
> IMO spend the $40 for Yagi Mech from DX Engineering and design for the
> wind velocity expected. Almost certainly some tube diameters will need
> single and perhaps double internal sleeving at spots. From my Y-M
> modeling experience, the center probably needs to be around 0.120" wall
> by 1.75" od for 6'+ each side of the boom. It is also a bit difficult
> to design full size 20 and 40m 80+ mph beams with only the 6' lengths
> from DX Eng, although I love their prices. A little work with YagiMech
> will illuminate why popular commercial 40m yagis are linear or coil or
> Moxon loaded, and why full size 3L ones weigh 300# and cost $5k. Think
> what 1/3 of that might look like. My 3L 40m came from an great Oregon
> ham builder and weighs 350# and is very experienced with wind and ice.
>
> Unless you really upscale sizes, a truss will be needed for full size
> 40m elements and while dacron is relatively low stretch, Phillystran is
> the standard for element trusses, essentially no stretch.
>
> I don't use hose clamps for elements over 1/2" diameter. Crossed
> machine screws keep elements snug in 2 planes with short overlaps, are
> strong, elements won't vibrate, and using nylocks they don't loosen.
>
> Then the more guys used = more wind resistance and worse the more ice
> loading.
>
> I think your dimensions will be easy to tune. NEC not needed.
> Mechanically you have the biggest challenge, IMO.
>
> 124' is a long way to climb to unscramble aluminum spaghetti.
>
> Grant KZ1W
>
>
> On 8/14/2018 18:45 PM, john@kk9a.com wrote:
> > In my opinion, this is very small tubing for a full sized 40m element. My
> > homebrew 20m beams use 1 1/4 diameter tubing tapered to 1/2 tips. I suggest
> > that you start by looking at the element taper schedules in the ARRL antenna
> > handbook.
> >
> > John KK9A
> >
> >
> > To: towertalk@contesting.com
> > From: terry burge <ki7m@comcast.net>
> > Date: Tue, 14 Aug 2018 13:11:18 -0700 (PDT)
> >
> > Hi Jim and group,
> >
> > Hell of a way to wake up in the morning. Anyway, here are the dimensions.
> >
> > DX Engineering aluminum tubing all 0.058" wall thickness
> > 1.250" X 6'
> > 1.125" X 6'
> > 1.00" X 6' Spit on the end allowing adjustment with 1/2 - 1 1/4" SS Hose
> > clamp
> > 0.875" X 6'
> > 0.750" X 3'
> > 0.625" X 3'
> > 0.500" X 6'
> >
> > Truss 1" X 1" X 0.125" X 3' aluminum angle 'iron' from Lowes. Holes drilled
> > to
> > also add a muffler clamp on the vertical truss if necessary to the mast.
> >
> > Center 'boom to mast' insulating clamp from SSS Solutions for 1.25" element.
> > A
> > little small but I figure it will work for my purposes with the trussing.
> >
> > Comtek 1:1 Current Balun at feed point.
> >
> > Because of Jim's thoughts about horizontal wind load I will also add another
> >
> > horizontal truss like I did with my quad array of something like 6' long
> > aluminum angle 'iron' with 3/16" Dacron truss lines. Hope this won't cause
> > too
> > much difficulty reaching the adjustment positions at the 1" to 0.875" slip
> > joint when rotating the vertical. Will do initial resonance dipping in on
> > test
> > support lower to the ground to get the SWR near where I need it around 7150
> > Khz. Not sure how much of a difference this will be at 124' versus my Comtek
> >
> > 4-Square ground mounted. Interesting experiment but since I have always felt
> >
> > lacking on 40 meters with 'knowing' I could work more stations in contest on
> > 40
> > meters with a better antenna system.
> >
> > I have not modeled this in Nec2 or whatever. Window 10 raises it's ugly head
> >
> > preventing that from operating. I know there are ways to deal with it but
> > I'm
> > not even sure the ARRL Antenna Book disk will run on my windows. And
> > programming computers is not one of my great accomplishments to say the
> > least!
> >
> > I have found when I build something like this I learn more in the building
> > and
> > seeing just how big and how much of a load things will be. Might say I try
> > to
> > go by feel and try to 'over built' to handle stresses like wind load. Not
> > always of course but I do think this will work here in Oregon.
> >
> >
> > Terry
> > KI7M
> >
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|