MIKE!!
Just to verify, you are putting a 1/4 wavelength 20m Shorted stub and a 1/4
wavelength 10m Shorted stub in parallel with the coax line at your transmitter
while you are transmitting on 40 m, correct?
If that is correct.....
A 1/4 wave length SHORTED stub will look like an OPEN to the 20m and 10m
harmonic of your transmitted signal and DO NOTING to the harmonic transmitted
signal!!
That is exactly what you are seeing, is it not?
You need an 1/4 wavelength 20M OPEN stub and a 1/4 wavelength 10m OPEN stub
which will short out the 20m and 10m signals as they leave your transmitter.
The 10m and 20m stubs should be located several feet apart on your transmit
line as an isolator between them.
I would try one stub at a time to be sure it performs as an open stub should
before you combine them on the transmit coax.
Bill N3RR
-----Original Message-----
From: CQ-Contest [mailto:cq-contest-bounces@contesting.com] On Behalf Of Mike
Smith VE9AA
Sent: Tuesday, September 08, 2015 5:14 PM
To: towertalk@contesting.com; cq-contest@contesting.com
Subject: Re: [CQ-Contest] Coax Stubs for SO2R
Thanks for the many replies so far. So today after I got home from work I
tried just running radio A @ about 1w on 7.000MHZ and saw S9 on 20m and s1 on
10m.
No change switching stub in or out, so I took Jim�s(K9YC) suggestion and moved
the stub farther away from the transceiver. I made up 3 random length patch
cables and so have the stub roughly either:
10-12�, 15�-17, 20�-22, 25�-27 away from the transmitter (Radio A). (rough
guesstimates) ( a 1/4wl, accounting for VF would be in the 23�-27� range)
No perceptible change whatsoever at any point in the line no matter where I put
the stub. Just the slightest SWR change when I put it in line. Almost cannot
detect it.
I am going nuts.
It�s either something in the shack or something outside rectifying (I guess?)
but these are pretty low power levels. (usually 100w, but also at 1w !)
Radio A (transmitter in the scenario) is hooked to an amp (not turned on in
close to a year), an antenna switch, a tuner/wattmeter (used on straightthrough
function only, just for it�s wattmeter/SWR function.)
Radio B (receiver in this scenario) is hooked to its own power supply and coax
straight outside to a multiband dipole some 100� from the Radio�s A�s various
antennas. No SWR meters, switches or anything.
They share a 4� hole in the wall in the garage where they exit to the outside,
where the RG8 or LMR400 coax;�s could be close to one another.
They share 120VAC in the shack (but different power supplies)
I have two additional (perhaps important?) questions. Should any of these
harmonics between any bands sound pure and �clean�, like a real CW signal?
Mine all sound low/muffly, wide, growly, like they have buzzing/humming AC
riding on top of them.
Additionally, the AA-230pro�s manual says to make the 1/4WL stub with the end
of the coax OPEN. . . . .but then for the purposes of these tests, I am using
the stubs shorted.
Maybe I have a ground loop somewhere and there is feedback or an isolation
problem on the shacks�s 120VAC line?
Mike
_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2015.0.6125 / Virus Database: 4409/10599 - Release Date: 09/08/15
_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest
|