Hans,
Both pipe dope and teflon tape are primarily lubricants to enable tightening
the fittings enough to achieve a seal. The thread dope is a mix of lubricant
grease and microscopic metallic particles to help prevent galling. I would be
concerned about putting a conductive grease in a fitting that needs two
distinct conductors.
Thomas W Noel
KF7RSF
> On May 26, 2015, at 10:25 AM, Hans Hammarquist via TowerTalk
> <towertalk@contesting.com> wrote:
>
> Hi Jim,
>
>
> I was thinking about the "gray" thread sealer that doesn't harden. It would
> also be out of the UV-radiation being inside the threads. Should be no
> problem, more than cleaning the gook off.
>
>
> I don't like to "tighten with pliers" when you have a knurled surface on the
> nut (or screw for that matter). It's needed for the UHF connector but not on
> the N (or TNC) for a proper connection.
>
>
> Regarding N <-> BNC: The BNC is weather proof by specification. You will find
> a gasket on a "correct" BNC connector. I was also told that the cores of the
> BNC and the N connector as almost identical. You can, with good result,
> temporary push a male N onto a female BCN. The core of a male BNC also fit in
> the female N. You can check the dimensions for the N and the BNC you will
> find that they are within tolerances. The center conductor in the N is
> thicker to maintain the Z=50 Ohm, as there is no dielectric (beside air)
> surrounding the conductor.
>
>
> Hans
>
>
>
> -----Original Message-----
> From: Jim Brown <jim@audiosystemsgroup.com <mailto:jim@audiosystemsgroup.com>>
> To: towertalk <towertalk@contesting.com <mailto:towertalk@contesting.com>>
> Sent: Mon, May 25, 2015 11:02 pm
> Subject: Re: [TowerTalk] Fwd: sealing PL259's
>
>
> On Mon,5/25/2015 6:49 PM, Hans Hammarquist via TowerTalk wrote:
>> Maybe even better; the type of plumber dope they use to seal the threads.
>
> When thinking about these materials, always consider the need to remove
> them. :) 3M 2228 and 33 are very good in this regard. Also UV. Using a
> product (like plumber dope) away from its usual application requires
> answers to questions like this. :)
>
>> What I don't like with the PL-259 is the lack of springs to keep the
> connection good at the screen side. All other connectors have some type of
> spring that ensure a good connection such as BNC and N. You have to tighten
> the
> PL-259 "well" in order to keep a good contact and there are no insurance they
> will loosen up over time.
>
> Tightening a UHF or N connector with pliers is part of mating it. If
> you're not doing that, you're not doing it right. I consider a quality
> UHF at least as robust as N (remember the migration problem). I don't
> consider BNC a weatherproof connector, nor a good connector for
> permanent installations. Rather, I view it as one that is more suited for
> mating and un-mating, indoors, where systems are often being
>
> reconfigured.
>
> 73, Jim
> K9YC
>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com <mailto:TowerTalk@contesting.com>
> http://lists.contesting.com/mailman/listinfo/towertalk
> <http://lists.contesting.com/mailman/listinfo/towertalk>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|