Harbor freight has a very handy butane unit. It's got a soldering tip and
(importantly) a built-in igniter.
http://www.harborfreight.com/butane-pencil-torch-41169.html
73/jeff/ac0c
www.ac0c.com
alpha-charlie-zero-charlie
-----Original Message-----
From: AB2E Darrell
Sent: Thursday, November 20, 2014 11:14 AM
To: Jim Thomson ; towertalk@contesting.com
Subject: Re: [TowerTalk] Cordless solder irons
I had a hand-held butane soldering iron that worked well out of the house.
A quick search on eBay shows both butane and also some battery powered
soldering irons.
73 Darrell AB2E
From: jim.thom@telus.net
To: towertalk@contesting.com
Date: Wed, 19 Nov 2014 06:43:55 -0800
Subject: [TowerTalk] Cordless solder irons
Date: Tue, 18 Nov 2014 19:10:23 -0800
From: "Don " <w7wll@arrl.net>
To: "Towertalk" <towertalk@contesting.com>
Subject: Re: [TowerTalk] Some advice about crimp ;type coax connectors
Which brings a question to mind. Why is there not available for sale a
decent battery powered soldering iron. Sure would be nice when in the air
not to be tied to an AC power cord. I did a search (probably not very
deep)
and found some battery powered irons but nothing that would deal with a
few
UHF connectors out and away from the 'house'. A friend from Australia who
was in the 2-way radio business had a couple he brought when he immigrated
from Oz but I've been unable to find that they are made anymore.
Anyone have information on such a tool for use whilst up in the air??
Don W7WLL
## from 1979-1989...in the telco I worked in 400 miles north of here, we
had
a cordless, rechargeable soldering iron. Think it was a weller...was
orange in colour.
Worked superb.... but never tried it outside.. only inside. They were
real small, light weight,
fit in your pocket. A lot smaller than a normal pencil iron. I believe
they would work fine
outside. A comment here. Silver plated PL-259s are a LOT easier to
solder vs
the nickel plated types. I gave up on amphenol nickel plated /teflon
PL-259s.
## I picked up 2 dozen van gordon silver /teflon PL-259 years ago.
They solder
real easy.
## Id check out cordless types 1st. You can probably get em with spare,
quick swap out
lithium batteries no doubt. The propane /butane types would also work,
but are more cumbersome
heavy etc... esp up a tower. In good wx... Id run an extension cord up
the tower..and use my
american beauty 100 w iron, with the .375 inch chisel tip. We used
dozens of those irons in the telco,
back when a lot of wiring was still being soldered. I have a few of
them. You can also get the bigger
ones, like 150w and up to 600 watt. The 100 w version... used to solder
a silver plated coax connector,
is super fast. The bigger ones like the 500-600w are used for
plumbing..where a blow torch cant be used.
The bigger ones work great for stuff like tubing type tank coils, large
wide cu strap, etc.
Jim VE7RF
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|