I have a Milwaukee Hole Shooter 3/8 corded reversible variable speed
drill. It is over 30 years old and going strong. It has enough torque
to hurt you if say using a hole saw or large bit and it jams. The drill
does not stall. It will wrap you up in the cord making it very
difficult to release the trigger and can hurt you. I have a Hole Hog
(little brother to the drill touted for tower raising) and it is a
powerful tool which can also hurt you if you jam a hole saw or large bit.
I do not have the model touted for tower raising (Super Hog) but it is
reasonable to assume in the progression of hole Shooter to Hole Hog to
Super Hog that the torque capable of being produced escalates with
increasing drill motor size. I don't argue against using the Super Hog
and would use one myself if the situation warranted it but... be
prepared, it is altogether likely you will not be able to hand hold it
if the tower jams. The torque will spike and if the chuck becomes
stationary the drill motor itself will in fact rotate with or without
your body parts clinging to it. These drills have provision for a second
hand grip (removable) which you should use. You should think ahead in
positioning your hands and your body so that if the tower should jam
causingt the drill itself to rotate you won't be injured. These tools
are powerful and capable of doing you grievous harm if you are unwary.
If I were to employ a Super Hog as a tower raising tool (altogether
reasonable possibility) I would design/build a mechanical bracing system
to prevent the drill from rotating if the chuck was stopped by such as
the tower jamming for some reason.
Milwaukee tools have served me well. I don't know that all Milwaukee
tools are high quality but all the ones I have are. I have a Sawzall
and the Hole Shooter that I have used a lot which are both over 30 years
old now. I replaced the power cord on the drill. It is a twist lock
connector that connects the cord to the drill and is trivial to change.
My Hole Hog is only10 years old but I expect it to last.
Want a chuckle? I traded a home built Heathkit H-8 computer and monitor
to a tool store owner for the Sawzall, Hole Shooter, and a worm drive
Skill saw around 1980-82. All these tools are still working perfectly.
The computer, if working, would at best be a historical curiosity.
Patrick NJ5G
On 2/21/2014 8:51 PM, Bryan Swadener wrote:
I may not be quite correct about the length of time but,
whatever it is, it ain't much. Because I'm using the Hy-Gain
HD300 rotator, the top section of the TX472 won't _QUITE_
crank all the way down. IIRC, the tower is 28' tall when
nested. The VERY heavy 15' L x 1/4" wall x 2" OD steel
mast protrudes out of the top of the tower approximately
11 feet, with my F-12 C-4XL just above the tower. I have
my Cushcraft AR10 adapted to fit the top of the mast,
adding another 16 feet. Even with all that above the tower,
The Super Hawg doesn't flinch AT ALL. I necessarily need
to hang on, and make certain nothing is in the way because,
it's a monster!
vy 73,
Bryan WA7PRC
--------------------------------------------
On Fri, 2/21/14, Mike NF4L wrote:
Subject: Re: [TowerTalk] Drill motor
To: Bryan WA7PRC
Cc: towertalk reflector
Date: Friday, February 21, 2014, 6:35 PM
Bryan -
That's fast! I have been trying to figure out how much
hassle it would be to adapt the TRX80HD to the HyGain tower.
If it's even possible.....
Mike
On Feb 21, 2014, at 9:20 PM, Bryan WA7PRC
wrote:
> Hi Mike,
>
> Mine does that, too... tilts up/down in about 30
seconds or so.
> I have US Tower's HD "raising fixture".
>
> An additional benefit of using the Super Hawg is, I can
also bore
> holes... in just about ANYTHING.
>
> vy 73,
> Bryan WA7PRC
> --------------------------------------------
> On Fri, 2/21/14, Mike NF4L
wrote:
>
> Subject: Re: [TowerTalk] Drill motor
> To: Bryan WA7PRC
> Cc: towertalk reflector
> Date: Friday, February 21, 2014, 6:15 PM
>
> Thanks Bryan -
>
> My application will be making the tower lie down and
sit up,
> so the load would be a bit different ..... maybe. I
talked
> to a local big name Milwaukee dealer here today. He
thought
> a Super Hawg was a Harley.
>
> I'm looking at wheelchair motors also, and a Fulton
KW3000.
>
> 73, Mike NF4L
>
> On Feb 21, 2014, at 8:52 PM, Bryan WA7PRC
> wrote:
>
>> IIRC, my US Tower TX-472 + Force12 C-4XL goes
up/down
> in
>> a little over 30 seconds, using a Milwaukee Super
Hawg
> (pn
>> 1680-20) that runs at 450rpm. It pulls 13A
at
> full load and
>> should not be confused with the smaller Hole Hawg.
The
>> tower uses Fulton K-2550 winches.
>>
>> The only issue with taking my tower up/down in 30
> seconds is,
>> I have several feedlines hanging off the tower,
along
> with two
>> wire antennas. I HAVE TO stop periodically
in
> order to keep
>> things from tangling. So far, it runs stone cold.
>>
>> I found the Super Hawg as a factory refurbished
unit on
> eBay
>> for a little over $200 shipped.
>>
>> vy 73,
>> Bryan WA7PRC
>> --------------------------------------------
>> Date: Thu, 20 Feb 2014 12:04:40 -0500
>> From: Roger K8RI
>> Subject: Re: [TowerTalk] Drill motor
>>
>> On 2/20/2014 9:55 AM, Mike NF4L wrote:
>>> I ran across the DeWalt DWD460 drill. It draws
11
> amps,
>> and has continuously variable speeds in 2 ranges( 0
300
> and
>> 0 1300 RPM). Seems like that would get away from
the
>> overheating problem in the worm-gear winches.
>>
>> There are rating and there are ratings. Most drill
> motors
>> are rated for
>> intermittent duty with short run times and long
> cooling
>> cycles.
>>
>> I purchased the largest Dewalt that Lowe's carries.
>> Drilling 3/4" holes
>> in 1/2" thick I-beam, I burned it up in less than
5
> minutes
>> and I had
>> just purchased it.
>>
>> Drill motors for mixing as have been listed on here
may
> be
>> rated
>> differently, or with a larger reserve/safety
factor
> than
>> those for
>> drilling holes. IOW two motors rated at 13A
with
> one
>> for mixing and one
>> for drilling may not have the same ability to raise
a
>> tower.
>>
>> I've not found a correlation in the ratings.
> From
>> experience, I've
>> found a drastic difference in ratings for drill
motors
> rated
>> for long
>> run times VS the typical short run times for
drilling
>> holes.
>>
>> I'd limit my purchases to a motor rated for long
run
> times
>> such as mixing.
>>
>> Caveat Emptor
>>
>> 73
>>
>> Roger (K8RI)
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4335 / Virus Database: 3705/7116 - Release Date: 02/22/14
_______________________________________
No infections found in this incoming message
Scanned by iolo System Shield
http://www.iolo.com
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|