Re: [TowerTalk] Rohn 45AG4 guy tabs?

["Mark Robinson" <markrob@mindspring.com>]

Yes, I installed my guys about 5 feet down from the top of my Rohn 45 tower 
and the rotator is about 8 feet down from the top of the tower. It seems to 
work out pretty well.
I took the advice of others, when I decided where to position the top guys. 
It cost the price of an additional guy bracket but I don't regret the 
decision.

Mark N1UK


----- Original Message ----- 
From: "Jim W7RY" <w7ry@centurytel.net>
To: "Mark Robinson" <markrob@mindspring.com>; "Jay Kesterson" 
<k0gu@verinet.com>
Cc: <TowerTalk@contesting.com>
Sent: Friday, 16 August, 2013 8:11 PM
Subject: Re: [TowerTalk] Rohn 45AG4 guy tabs?


> I agree. Having the guys on the top plate is a real pain. My first Rohn 25 
> was like that. It was very frustrating installing a beam with a tram 
> system.
> Install a guy ring 4-5 feet down the tower.
> 73
> Jim W7RY
>
>
> -----Original Message----- 
> From: Mark Robinson
> Sent: Friday, August 16, 2013 1:59 PM
> To: Jay Kesterson
> Cc: TowerTalk@contesting.com
> Subject: Re: [TowerTalk] Rohn 45AG4 guy tabs?
>
> Yes I believe that they can be used to secure the guys. I chose not to do
> this since it is already cluttered up there and having the guys attached 
> to
> the top plate makes working on the antennas more difficult.
>
> The angled down guy anchor points on the top plate made a good point to
> secure the coax loop though.
>
> I mounted my top guys several feet below the top plate.
>
> 73 Mark N1UK
>
>
>
> ----- Original Message ----- 
> From: "Jay Kesterson" <k0gu@verinet.com>
> To: "Tower Talk" <TowerTalk@contesting.com>
> Sent: Friday, 16 August, 2013 4:42 PM
> Subject: [TowerTalk] Rohn 45AG4 guy tabs?
>
>
> >   I see at least one Rohn 45 seller's web site that calls the tabs on the 
> > 45AG4 top plate guy tabs. However I don't see any reference to that in 
> > the Rohn documentation. Except for dimensions Rohn doesn't really say a 
> > lot about the 45AG4. But Rohn always shows the guys attached a few feet 
> > below the tower. So are they guy tabs? I was planning on using them on a 
> > tower with a tall mast (the mast is another subject that will get a post 
> > here in a bit). Guy the tower at the top plate and then not far under the 
> > rotator. Anyone have the scoop on this.
> > 73,  Jay  K0GU
> >
> >
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk 
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk