Towertalk
[Top] [All Lists]

Re: [TowerTalk] Bull pin / drift pin

To: towertalk@contesting.com
Subject: Re: [TowerTalk] Bull pin / drift pin
From: ROBERT HARMON <k6uj@pacbell.net>
Date: Mon, 29 Aug 2011 10:41:07 -0700
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Heres a source for drift pins that structural steel fitters use for reference.

http://www.ajaxtools.com/prodlist.php?dept_id=11

73,
Bob
K6UJ






On Aug 29, 2011, at 10:33 AM, Pete Raymond wrote:

> I have found Drift Pins in the tool section of Sears.  They carry a few 
> different sizes, a great tool.
> 73 Pete N4KW
> 
> ----- Original Message ----- 
> From: <TexasRF@aol.com>
> To: <dieven@comcast.net>; <towertalk@contesting.com>
> Sent: Monday, August 29, 2011 7:48 AM
> Subject: Re: [TowerTalk] Bull pin / drift pin
> 
> 
>> Dick, you might try an automotive parts store. Many of them have some
>> pretty big tools to sell.
>> 
>> 73,
>> Gerald K5GW
>> 
>> 
>> 
>> 
>> In a message dated 8/29/2011 6:29:18 A.M. Central Daylight Time,
>> dieven@comcast.net writes:
>> 
>> I find  myself without a drift pin to align the leg holes in Rohn 55G 
>> tower
>> sections (5/16” bolt size).  I need to pull together several  sections on
>> the
>> ground with a couple of come-alongs.  We plan to use a  crane to lift
>> preassembled sections and I don’t to do these one at a time  at crane 
>> rental
>> rates.
>> 
>> 
>> 
>> Where do I find a good drift pin /  bull pin / barrel pin for this 
>> purpose?
>> Klein Tools and  SteelErectorTools.com offer some really hefty ones for
>> steel
>> construction,  and I’ve found little drift punch sets at Sears and Ace
>> Hardware and Harbor  Freight, but not one that’s about the right size for
>> this. I think a ¼”  point diameter would be about right, maybe the large
>> diameter would be ¾”,  perhaps 6” long?
>> 
>> 
>> 
>> Something that cleared the holes a little bit  so I didn’t have to force 
>> the
>> bolts through would be helpful.  These  are new sections that haven’t met
>> one
>> another before. I got the top plate  on with a rubber mallet, but that’s 
>> not
>> going to work with 100# tower  sections.
>> 
>> 
>> 
>> Thanks!
>> 
>> 
>> 
>> Dick,  K6KR
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> _______________________________________________
>> 
>> 
>> 
>> _______________________________________________
>> TowerTalk  mailing  list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>> _______________________________________________
>> 
>> 
>> 
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>> 
> 
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>