Towertalk
[Top] [All Lists]

Re: [TowerTalk] Anti-climb panels for a crank-up tower

To: <towertalk@contesting.com>
Subject: Re: [TowerTalk] Anti-climb panels for a crank-up tower
From: "Keith Dutson" <kjdutson@earthlink.net>
Reply-to: keith@dutson.net
Date: Thu, 14 Apr 2005 08:58:52 -0500
List-post: <mailto:towertalk@contesting.com>
Put a simple, easy-to-read sign at eye level that reads:

"WARNING - 100,000 VOLTS - CLIMBERS WILL BE VAPORIZED 20 FEET ABOVE THIS
SIGN!"

Any kid too young to read and understand this sign is too dumb to climb very
high anyway. :)

Keith NM5G

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of
Robert_Redoutey@Dell.com
Sent: Thursday, April 14, 2005 8:26 AM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Anti-climb panels for a crank-up tower

Craig,

I know it's important to keep the beauty of the tower from being taken away
by some "Anti-climb" panel. My suggestion is a wood lattice panel.
Much better than any sort of "fencing" or paneling. The base around my tower
is several inches above the ground, running 4' square. Having it up along
the side of the base allows clearance around the tower, and allows for easy
support. Run 1 x 1's around the top, inside of the lattice for support along
the top. Could be painted green to "blend in"
with surrounding grasses/trees.

Bob, N5KF
Georgetown, TX



Message: 4
Date: Wed, 13 Apr 2005 22:53:27 -0700
From: "Craig Sande" <craig.sande@sbcglobal.net>
Subject: [TowerTalk] Anti-climb panels for a crank-up tower
To: <towertalk@contesting.com>
Message-ID: <000001c540b6$47bc8590$3459fea9@LAPTOP>
Content-Type: text/plain;       charset="us-ascii"

I would like to get/make an anti-climb device for my tower.  It is a 70'
motorized crank-up/pull-down tower by Tashjian Towers.  I won't be able to
clamp anything around the legs because of the moving contact points between
the tower sections.  In addition, the motor, gear box, and cable drum
protrude at the bottom.  I was thinking that a sheet metal shield starting
above the level of the motor, bear box, and drum might work, but am unsure
how it could be attached without interfering with the moving parts of the
tower.  A fence around the tower is out of the question for aesthetic
reasons, therefore my only option is to fence in the back yard.  Does anyone
figured out how to make an anti-climb device for such a tower?
 
Craig, AE7I



        Bob Redoutey
        Regulatory Test
        Dell Inc.
        512-728-0011 (Office)
        512-423-8394 (Cell)
        512-728-5811 (Lab)


_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless Weather 
Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any questions 
and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>