Towertalk
[Top] [All Lists]

Re: [TowerTalk] Re: Thrust bearing

To: <kb9cry@comcast.net>, "Noel" <yaesurig@msn.com>,<towertalk@contesting.com>
Subject: Re: [TowerTalk] Re: Thrust bearing
From: "Jerry Keller" <k3bz@arrl.net>
Date: Thu, 22 Jul 2004 15:48:48 -0400
List-post: <mailto:towertalk@contesting.com>
I use two thrust bearings, one at the top and one a couple of feet down the 
mast. The rotator is a couple of feet below the bottom TB. The top TB is merely 
a guide; the bottom TB supports all (or nearly all) the weight of the mast and 
antennas via two opposing "double-saddled" muffler clamps on the mast. The mast 
doesn't actually bear much on the rotator... the rotator merely grips the mast 
and turns it. I figure the less weight that bears on the rotator, the longer it 
will last.... and TB's are cheaper than rotators!  I do have the mast pinned to 
the rotator, however, as the Yaesu rotator provides for pinning. 
This is my first tower, but this arrangement seems to work A-OK for me. I've 
had no slipping or other problems with it.

73,  Jerry K3BZ
  ----- Original Message ----- 
  From: kb9cry@comcast.net 
  To: Noel ; towertalk@contesting.com 
  Sent: Thursday, July 22, 2004 2:46 PM
  Subject: RE: [TowerTalk] Re: Thrust bearing


  I have TB-3 on my towers and what I do is set the mast down into and resting 
on the rotator.  I center the mast in the thrust bearing and tighten the collar 
screws, really just to keep it centered.  I then install a small SS pipe clamp 
onto the mast and move it down the mast so it is up against the top of the 
bearing.  I then install the antenna.  My assumption is that some of the 
additional load from the antenna is being borne by the TB.  Seems to work for 
me.  If I need to remove the rotator, I've installed another pipe clamp up the 
mast above the top bearing plate and used a small scissors jack to jack the 
mast assembly up and out of the rotator.  On the new tower I might attach a 
come-along to a clamp attached on the mast just above the rotator and jack it 
up that way.  Phil  KB9CRY

  -------------- Original message -------------- 

  > Agreed with everthing except the statement. "...Then make sure the 
  > collar can rotate around the mast without binding".. Seems to defeat the 
  > point of having a thrust bearing? Why not have just a collar then? I 
  > think the bolts in the thrust bearing should be tightly holding the mast 
  > or at least very snug. Not bearing weight but enough to support any 
  > lateral movement. Your method would cause the bolts to eventually scar 
  > the mast even though you say the clearance is minimal, unless one used 
  > shims. 
  > 
  > I'm curious haw many people who utilize thrust bearings, allow the 
  > bearing to "rotate around the mast" or make sure the mast and bearing 
  > are tight and rotate together? 
  > 
  > 
  > Noel 
  > 
  > 
  > _______________________________________________ 
  > 
  > See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless 
Weather 
  > Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any 
questions 
  > and ask for Sherman, W2FLA. 
  > 
  > _______________________________________________ 
  > TowerTalk mailing list 
  > TowerTalk@contesting.com 
  > http://lists.contesting.com/mailman/listinfo/towertalk 
  _______________________________________________

  See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless 
Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any 
questions and ask for Sherman, W2FLA.

  _______________________________________________
  TowerTalk mailing list
  TowerTalk@contesting.com
  http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless Weather 
Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any questions 
and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>