I vaguely remember that the manual has an error in the adjustment
procedure. Someone on the list probably has the correction. I found it on
the web.
I tweeked mine using the corrected procedure and it still has more than 100
watts on a couple of bands.
My OMNI 6+ is sitting on the shelf. Trying to decide if I want to sell it
or not. Mighty fine CW.
Doug N4IJ
On Sun, Apr 22, 2018 at 11:00 AM, <tentec-request@contesting.com> wrote:
> Send TenTec mailing list submissions to
> tentec@contesting.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.contesting.com/mailman/listinfo/tentec
> or, via email, send a message with subject or body 'help' to
> tentec-request@contesting.com
>
> You can reach the person managing the list at
> tentec-owner@contesting.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of TenTec digest..."
>
>
> Today's Topics:
>
> 1. omni VI plus TX power (Gary Hendricks)
> 2. omni VI plus TX power (Peter Bertini)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Sat, 21 Apr 2018 16:52:52 -0600
> From: "Gary Hendricks" <k4mt1950@charter.net>
> To: "'tentec@contesting.com'" <tentec@contesting.com>
> Subject: [TenTec] omni VI plus TX power
> Message-ID: <dAss1x0023T8cn001AssNi@charter.net>
> Content-Type: text/plain; charset=UTF-8
>
> I just acquired a very nice omni VI plus and it works great. Only
> thing so far that seems off is TX power is way over 100 W. ALC seems
> to be working as I can adjust it to 100 W with drive control. Is there
> a TX power adjustment that someone has cranked up?
> Gary K4MT
>
>
> ------------------------------
>
> Message: 2
> Date: Sun, 22 Apr 2018 11:01:30 -0400
> From: Peter Bertini <radioconnection@gmail.com>
> To: tentec@contesting.com
> Subject: [TenTec] omni VI plus TX power
> Message-ID:
> <CA+uDY2QNnJem6vLGf05MVSP4hOHkDnaKtBqudzOnNov=UW_2gg@mail.gmail.
> com>
> Content-Type: text/plain; charset="UTF-8"
>
> There is an ALC and IC current limiting pot on the rear of the 9 MHz
> board. Both control maximum power.
>
> In your case, I suspect someone has cranked down the ALC pot to allow the
> rig to generate more than 100 watts. I'd bet IMD suffers at those higher
> power levels.
>
> Assuming you trust your wattmeter/dummy load, you can check the manual for
> the procedure to set the ALC pot. The current limiting pot is a bit more
> involved. But I bet the ALC limit pot will do what you need. I set my Omni
> VI rigs for a 75 watt maximum, which is more than enough to drive my SB-220
> and my ALS-1300.
>
> Pete k1zjh
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> ------------------------------
>
> End of TenTec Digest, Vol 184, Issue 16
> ***************************************
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|