Thanks Greg,
I keep muffin fans blowing on the rig's heat sink and power supply's heat sink
most of the time already.
Later, Joe, K8MP
Sent from AOL Mobile Mail
-----Original Message-----
From: Greg S via TenTec <tentec@contesting.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Cc: Greg S <oldlongbeard@yahoo.com>
Sent: Fri, Mar 2, 2018 06:37 PM
Subject: Re: [TenTec] Winlink and Winmoor on an Omni 6 Plus
The radio address is different, if it matters, and I would be sure to get a fan
on your heatsink.
Greg KC8HXO
--------------------------------------------
On Fri, 3/2/18, Joe Papworth via TenTec <<a
href="mailto:tentec@contesting.com";>tentec@contesting.com</a>> wrote:
Subject: Re: [TenTec] Winlink and Winmoor on an Omni 6 Plus
To: <a href="mailto:w7zrc@yahoo.com";>w7zrc@yahoo.com</a>, <a
href="mailto:tentec@contesting.com";>tentec@contesting.com</a>
Cc: <a href="mailto:k8mp@aol.com";>k8mp@aol.com</a>
Date: Friday, March 2, 2018, 5:38 PM
Thanks Rod. I'll check it
out.
Later, Joe, K8MP
Sent from AOL Mobile Mail
-----Original Message-----
From: Rod Greene via TenTec <<a
href="mailto:tentec@contesting.com";>tentec@contesting.com</a>>
To: Discussion of Ten-Tec Equipment <<a
href="mailto:tentec@contesting.com";>tentec@contesting.com</a>>
Cc: Rod Greene <<a href="mailto:w7zrc@yahoo.com";>w7zrc@yahoo.com</a>>
Sent: Fri, Mar 2, 2018 05:34 PM
Subject: Re: [TenTec] Winlink and Winmoor on an
Omni 6 Plus
Joe, seems like I used Icom 735 (some older
version like that) with my Paragon that has an N4PY chip.
The Omni 6 may be the same
GL es 73,
Rod/w7zrc
From: Joe Papworth via TenTec
<<a href="<a
href="mailto:tentec@contesting.com";>tentec@contesting.com</a?">mailto:tentec@contesting.com";>tentec@contesting.com</a</a>>>
To: <a href="<a
href="mailto:tentec@contesting.com";>tentec@contesting.com</a?">mailto:tentec@contesting.com";>tentec@contesting.com</a</a>>
Cc: <a href="<a
href="mailto:k8mp@aol.com";>k8mp@aol.com</a?">mailto:k8mp@aol.com";>k8mp@aol.com</a</a>>
Sent: Friday, March 2, 2018 2:08 PM
Subject: [TenTec] Winlink and Winmoor on an
Omni 6 Plus
Gents,
Winmoor does not support the Omni 6 Plus in
their Rig Control software.
I'm thinking
that someone once told me there was a different brand and
model that used a command set equal to or very similar to
the Omni 6.
Does that ring any bells?
Or, has anyone found another
work-around for this problem?
Thanks, Joe, K8MP
_______________________________________________
TenTec mailing list
<a
href="<a
href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a?">mailto:TenTec@contesting.com";>TenTec@contesting.com</a</a>>
<a href="<a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>"
target="_blank"><a
href="http://lists.contesting.com/mailman/listinfo/tentec</a"
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a</a>>
_______________________________________________
TenTec mailing list
<a
href="<a
href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a?">mailto:TenTec@contesting.com";>TenTec@contesting.com</a</a>>
<a href="<a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>"
target="_blank"><a
href="http://lists.contesting.com/mailman/listinfo/tentec</a"
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a</a>>
_______________________________________________
TenTec mailing list
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
<a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
_______________________________________________
TenTec mailing list
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
<a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|