Sounds good, continued luck Steve!
Barry N1EU
On Tue, Sep 26, 2017 at 1:19 PM, Steve <sswhite@mchsi.com> wrote:
> Some progress...It receives now!!!! You ask what did I do....
>
> 1. Resoldered the CPLD and DSP chips.
> 2 Carefully cleaned the flux off of them and closely inspected them with
> eye loop, found little hair like things across several leads and also on
> the mutipin connectors.
> 3. At first this made no difference using real old ver 1 software that I
> had installed yesterday
> 4. Loaded up the latest Ver3 software and could see that it loaded
> correctly and I had DSP software loaded correctly ( big step forward)
> but still no audio or reception.
> 5. Followed very closely to the letter the re boot procedure and it
> worked!! Had audio and could hear stuff on 20M ssb but still a few
> issues.
> 6 Reloaded the software again and careful to follow the reboot and it
> worked.
> 7 Went to button up the front panel to the case and it quit working????
> Darn
> 8 . Tried restart/reboot and now the front panel is attached to the case
> and radio working on Rx anyway...
>
> So I will let it cook for awhile and see what give. I am not a fan of
> all the connectors in this radio and not sure they area all seating
> correctly...Connectors like this are bad and easily lead to
> funkyfailures.
>
> Will let you guys know of anything else I am going to get a new battery
> just in case the one I have is weak although it checks good..
>
> Steve NU0P Fingers crossed
>
>
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Barry
> N1EU
> Sent: Tuesday, September 26, 2017 9:56 AM
> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> Subject: Re: [TenTec] Orion problems
>
> FWIW, the Orion seems more prone to strange internal connectivity
> failures of one sort or another than the Orion II.
>
> Barry N1EU
>
> On Tue, Sep 26, 2017 at 10:48 AM, Barry N1EU <barry.n1eu@gmail.com>
> wrote:
>
> > This issue reminds me of a conversation on the Yahoo Groups Orion
> > group back on Feb. 16, 2014 called "Boot Failure on Orion 1",
> > initiated by
> > WB2NMI: https://groups.yahoo.com/neo/groups/orion565/conversations/
> > topics/9941
> >
> > I think the jist of it was intermittent logic board connections and
> > the PCB needed some resoldering and he enlisted the help of Arek AC2FC.
> >
> > Barry N1EU
> >
> >
> >
> > On Tue, Sep 26, 2017 at 9:28 AM, Steve <sswhite@mchsi.com> wrote:
> >
> >> One thing to remember is that I get no audio at all out. I can turn
> >> up both main and sub rx's gain and still get no audio. On my Omni II
> >> I can disconnect the antenna and turn the audio and hear at least
> >> rushing noise. There is a clue here I bet. Back to the radio...
> >>
> >> Steve
> >>
> >> -----Original Message-----
> >> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
> >> Steve
> >> Sent: Tuesday, September 26, 2017 8:12 AM
> >> To: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
> >> Subject: Re: [TenTec] Orion problems
> >>
> >> Voltages are good at the A( board but I will scope them this morning.
>
> >> It has been recapped. I checked the input to the Logic card of the
> >> both the main and sub receivers and can see them when I apply a
> >> 14.250 Mhz signal to the input. However, the Sub Rx input level is
> >> quite a bit higher than the main Rx input level.
> >>
> >> I too am trying to find the signal path thru the logic board to find
> >> out why the boot sequence will not see the V2 mod. The V2 Mod is one
> >> wire and two cuts. I have checked it and the mod is there and
> correct. .
> >> Probably should follow the signal path from the mod to the DSP's.
> >> The previous owner told me he woke up one morning and the radio would
> >> no longer work...
> >>
> >> Steve NU0P
> >>
> >> -----Original Message-----
> >> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Jeff
> >> (W4DD)
> >> Sent: Tuesday, September 26, 2017 4:53 AM
> >> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> >> Subject: Re: [TenTec] Orion problems
> >>
> >> I would start by confirming voltages on the A9 board. Also scope
> them.
> >>
> >> Then confirm they are getting to the dsp's.
> >>
> >> As I recall, the v2 mod is a single strap, but don't recall the
> details.
> >> I would focus on why the cpu can't read the strap. I'll try take a
> >> look at the schematic tonight.
> >>
> >> Not sure if anyone has ever pubished the boot sequence but that would
> >> be handy.
> >>
> >> On Sep 25, 2017 11:57 PM, "Steve" <sswhite@mchsi.com> wrote:
> >>
> >> The A9 board has been updated. Since there is output from the rcvr
> >> to the Logic board and no audio out of any kind it makes me wonder
> >> about the DSP and CODECS on that board. I went and loaded Ver 1
> >> software but that made no difference either.
> >>
> >> Steve
> >>
> >> -----Original Message-----
> >> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
> >> Peter Frenning [OZ1PIF]
> >> Sent: Monday, September 25, 2017 5:15 PM
> >> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>; Steve
> >> <sswhite@mchsi.com>
> >> Subject: Re: [TenTec] Orion problems
> >>
> >> Den 25-09-2017 kl. 22:31 skrev Steve:
> >> > Orion 1..Battery is good too...I wonder if I can put a 14 Khz
> >> > unmodulated signal into the DSP input (J20) and find out if the
> >> > whole DSP chain is working..
> >> >
> >> > Steve
> >> Has anybody suggested checking out the A9 board? Any of a whole box
> >> of Gremlins can emerge from troubles there. When mine (O2) started
> >> acting erratically I updated the thre 470uF electrolics to lower
> >> ESR/higher temp ones, and all my troubles went away, many other
> >> similar experiences has been related here over time.
> >>
> >> --
> >> Vy 73 de OZ1PIF/5Q2M, Peter
> >>
> >> ******************************************
> >> ** The day Microsoft makes something **
> >> ** that doesn't suck is probably the **
> >> ** day they start making vacuum **
> >> ** cleaners ! **
> >> ** -- Anonymous Wise Guy **
> >> ******************************************
> >> email: peter(no-spam filler)@frenning.dk
> >> http://www.frenning.dk/oz1pif.htm Ph. +45 4619 3239/ +45 2332 9464
> >> Snailmail:
> >> Peter Frenning
> >> Ternevej 23
> >> DK-4130 Viby Sj.
> >> Denmark
> >> ******************************************
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >
> >
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|