TenTec
[Top] [All Lists]

Re: [TenTec] 962 power supply {was 961 PWR Supply}

To: tentec@contesting.com
Subject: Re: [TenTec] 962 power supply {was 961 PWR Supply}
From: Joe Papworth via TenTec <tentec@contesting.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 27 Jun 2017 14:29:14 -0400
List-post: <mailto:tentec@contesting.com>
PS- Radio Shack used to stock the 25 amp version in their stores. Some of them 
may still have it.

Sent from AOL Mobile Mail


-----Original Message-----
From: Joe Papworth via TenTec <tentec@contesting.com>
To: tentec <tentec@contesting.com>
Cc: k8mp <k8mp@aol.com>
Sent: Tue, Jun 27, 2017 02:09 PM
Subject: Re: [TenTec] 962 power supply {was 961 PWR Supply}


It was a long time ago but it was probably the only place I found room. Or it 
could have been an existing screw or stud.
That bridge is toast.

Sent from AOL Mobile Mail


-----Original Message-----
From: Robert S Jenkins <<a href="mailto:qrp@kg4kgl.net";>qrp@kg4kgl.net</a>>
To: Discussion of Ten-Tec Equipment <<a 
href="mailto:tentec@contesting.com";>tentec@contesting.com</a>>
Sent: Tue, Jun 27, 2017 01:31 PM
Subject: Re: [TenTec] 962 power supply {was 961 PWR Supply}


Those values were with the bridge completely out of the circuit. 

Why did you mount it on the back of the front panel?

Tnx,

Robert
KG4KGL

> On Jun 27, 2017, at 13:25, Joe Papworth via TenTec <<a href="<a 
> href="mailto:tentec@contesting.com";>tentec@contesting.com</a?">mailto:tentec@contesting.com";>tentec@contesting.com</a</a>>>
>  wrote:
> 
> If the bridge is still in the circuit, that .2 ohm reading is the secondary 
> winding of the transformer.
> If it does end up being the bridge, I recommend you remotely mount the new 
> one somewhere. I put mine on the back side of the front panel. Use BIG wire. 
> (At least 12 gauge)
> And use heat sink grease.
> 
> Sent from AOL Mobile Mail
> 

_______________________________________________
TenTec mailing list
<a href="<a 
href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a?">mailto:TenTec@contesting.com";>TenTec@contesting.com</a</a>>
<a href="<a href="http://lists.contesting.com/mailman/listinfo/tentec"; 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>" 
target="_blank"><a 
href="http://lists.contesting.com/mailman/listinfo/tentec</a" 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a</a>>
_______________________________________________
TenTec mailing list
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
<a href="http://lists.contesting.com/mailman/listinfo/tentec"; 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>