TenTec
[Top] [All Lists]

Re: [TenTec] Orion II Black Screen - Successful Repair

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Orion II Black Screen - Successful Repair
From: denton sprague <denton@oregontrail.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 16 Dec 2016 09:00:45 -0800
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
my Orion I has a fading display….LED illumination going south? if so, what is 
the easiest/cheapest fix?

> On Dec 16, 2016, at 8:40 AM, Dukes HiFi <dukeshifi@comcast.net> wrote:
> 
> The Orion 1 had LED illumination, one of the first Ham radios to do so, 
> 
> I have never needed to open an Orion 2 display but I doubt that Ten Tec would 
> have stepped backwards this far unless they had a good reason.
> 
> Perhaps so, though, since Orion 2’s  did not use the white pair of wires 
> going from the power distribution board, the one that provided power for the 
> LED control circuit. If the O2 display had on board high voltage generation 
> on the CPU board (or on the display panel itself), that would obviate the 
> need for this white cable. 
> 
> It is possible Ten Tec was not able to find a color LCD that used LED 
> illuminators. If this was the case, then the LCD panel in use must have its 
> own on-board high voltage generator because the 566 schematic does not show 
> one and the LCD PWM driver from the 565 is missing from the 566. Thus it is 
> highly probable that the color display has its voltage generator on-board.
> 
> The person who found and repaired this gave us (myself at least) some very 
> valuable information and did a great repair!
> 
> Gary
> 
> W0DVN
> 
> 
>> On Dec 16, 2016, at 7:02 AM, Bob K8IA via TenTec <tentec@contesting.com 
>> <mailto:tentec@contesting.com>> wrote:
>> 
>> Steve,
>> 
>> This is in the Orion II. I dont believe the Orion is a cfl backlit display. 
>> Others should verify. Tnx.
>> 
>> 
>> 73, Bob K8IA
>> Arizona Outlaws Contest Club
>> 
>> <div>-------- Original message --------</div><div>From: Steve Ellington 
>> <steven4lq@gmail.com <mailto:steven4lq@gmail.com> 
>> <mailto:steven4lq@gmail.com <mailto:steven4lq@gmail.com>>> 
>> </div><div>Date:12/16/2016 5:40 AM  (GMT-07:00) </div><div>To: Discussion of 
>> Ten-Tec Equipment <tentec@contesting.com <mailto:tentec@contesting.com> 
>> <mailto:tentec@contesting.com <mailto:tentec@contesting.com>>> 
>> </div><div>Cc: BobK8IA@aol.com <mailto:BobK8IA@aol.com> 
>> <mailto:BobK8IA@aol.com <mailto:BobK8IA@aol.com>> </div><div>Subject: Re: 
>> [TenTec] Orion II Black Screen - Successful Repair </div><div>
>> </div>1,800 volts in an Orion!!! Better watch where you poke around!
>> 
>> That board would be a good item for Orion owners to stock up on.
>> 
>> On Thu, Dec 15, 2016 at 6:30 PM, bobk8ia--- via TenTec <
>> tentec@contesting.com <mailto:tentec@contesting.com> 
>> <mailto:tentec@contesting.com <mailto:tentec@contesting.com>>> wrote:
>> 
>>> 
>>> This is a follow up to my email below from 24 October 2016.
>>> 
>>> As of 12/14/16, my Orion II is successfully repaired now, thanks to good
>>> friend Kevin W9CF. What had failed was some component(s) on the 12v to
>>> 1800v
>>> inverter board that powers the cfl backlight.
>>> 
>>> A new inverter board (TDK CXA-L0612A-VJL which is DigiKey part #
>>> 445-1619-ND; about $23) has the radio up and running like new.
>>> 
>>> http://www.digikey.com/product-detail/en/tdk-corporation/CXA-L0612A-VJL/ 
>>> <http://www.digikey.com/product-detail/en/tdk-corporation/CXA-L0612A-VJL/>
>>> 445-
>>> 1619-ND/652720
>>> 
>>> Thought some of you real techies would like to know this. Thanks to those
>>> of you that responded to me directly.
>>> 
>>> 73, Bob K8IA
>>> Arizona Outlaws Contest Club
>>> 
>>> -----------------------
>>> 
>>> 
>>> In a message dated 10/24/2016 8:15:20 A.M. US Mountain Standard Time,
>>> BobK8IA@aol.com writes:
>>> 
>>> Gents;
>>> 
>>> I am getting ready for our annual Multi-Two N7AT fun in CQWW SSB, this
>>> weekend. One of the op positions my Orion II. I turned the Orion II on
>>> and no
>>> screen appeared, just blank/black. The radio appears to be functioning
>>> fine
>>> but no screen. It does not appear to be power supply related.
>>> 
>>> It worked fine two days ago (and generally trouble free since 2006 when I
>>> bought it new). Latest firmware 3.033xe installed and RX-366. Battery was
>>> recently replaced.
>>> 
>>> Any guidance you can give me. The radio is contest-unusable as is.
>>> 
>>> TNX.
>>> 
>>> 73, Bob K8IA
>>> Arizona Outlaws Contest  Club
>>> 
>>> 
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>> 
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com <mailto:TenTec@contesting.com> 
>> <mailto:TenTec@contesting.com <mailto:TenTec@contesting.com>>
>> http://lists.contesting.com/mailman/listinfo/tentec 
>> <http://lists.contesting.com/mailman/listinfo/tentec><http://lists.contesting.com/mailman/listinfo/tentec
>>  <http://lists.contesting.com/mailman/listinfo/tentec>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com <mailto:TenTec@contesting.com>
> http://lists.contesting.com/mailman/listinfo/tentec 
> <http://lists.contesting.com/mailman/listinfo/tentec>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>