Dragons are bad enough to deal with, much less re-balling them! My advice is
to let them
alone and you'll not be missing things that are important to your survival.
Clayton N4EV
--------------------------------------------
On Fri, 4/1/16, Wade Staggs <tvman1954@gmail.com> wrote:
Subject: Re: [TenTec] reballing a Dragon
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Date: Friday, April 1, 2016, 4:57 PM
*Really simplified version.... O.K.?
Back in the good old days, electronic
components had wire leads. Now we have SMT or Surface Mount
Technology. So
now on Microprocessors and other LSI or Large Scale
Integration components.
There are tiny Pads or Lands on the bottom of the device. At
the factory
these components have tiny Balls of solder on each lead,
sometimes over 200
leads or pin connections could be on the device. In the new
technology, the
Chip is placed on the board by a very fast and precise
machine. The board
will then go through a multi-stage Oven which has a minimum
of Heat-up,
Solder or Bond and then the cool down stage. Going through
this oven on a
conveyor belt, the oven can be over 50 feet long. The
circuit board has no
holes for component leads to pass through. I have repaired
many video games
and other devices with a simple Paint Stripping Gun. It
takes a light hand
and a handheld infrared thermometer is a must so that you
don't cook the
board. It is very easy to do lots more harm to the device.
Repairs of the
Xbox 360 have financed several of my Boat Anchor Restoration
Projects. Try
goggling " The Red Ring of Death "*
*
73 from Wade/KJ4WS*
On Fri, Apr 1, 2016 at 1:04 PM, Tony <va3dwi@gmail.com>
wrote:
> Showing my age here hi... hi. What's reballing?
Thanks.
> 73, Tony VE3DWI.
>
> Sent from my BlackBerry 10 smartphone on the Bell
network.
> Original Message
> From: John Henry
> Sent: Thursday, March 31, 2016 13:03
> To: tentec@contesting.com
> Reply To: Discussion of Ten-Tec Equipment
> Subject: [TenTec] reballing a Dragon
>
> The problem wasn't always in reballing.
> There were problems in that the part sat on a shelf for
15 years, not in a
> clean room, and somewhere along the line got hit with
ESD, or too hot one
> day, random circuits inside the chip failed, etc.
>
> I do however doubt that if 20 people tried to scavenge
some dragonballs and
> had to replace it, well, maybe 4 in 20 would be happy
at the end of the
> day, the other 16 would probably be buying a new rig.
just my two cents.
> So many pitfalls along the way, the chips are at least
15 years old,
> storage, excessive heat, etc.
> Yield of TEN-TEC trying to do this using a couple of
excellent BGA board
> houses to replace them was very low.
>
> 73, KI4JPL
> John Henry
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
--
*Living one day at a time with Jesus as my Savior. But,
still having Fun.*
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|