TNX Gary
________________________________________
From: TenTec <tentec-bounces@contesting.com> on behalf of gyates@dreamscape.com
<gyates@dreamscape.com>
Sent: Tuesday, March 15, 2016 2:06 PM
To: 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] Orion 2
Andy,
Try this
http://www.gainesvilletelevisionrepairshop.com/
Greg
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of P C Andy
Anderson
Sent: Tuesday, March 15, 2016 1:39 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Orion 2
Greg, do you have any contact information for Skyland Radio. Tried the web,
no good. Phone, web site, email etc
Tnx, Andy..W3LI
________________________________________
Thanks for the suggestion on the cable. I took the Orion 2 apart and sure
enough the cable to the sub was loose. Put it back on and so far it seems
to work like new.
Barry, as I discussed with you last year had a problem with the audio. I
sent to Skyland Radio in Georgia while I was in Fl. They had it repaired
and a few days and held it until I headed back to upstate NY. Radio arrived
1 day before me.
Anyway, I have heard good reports on the company. Anyone interested google
it and check out their facebook page. They work on things like reel to reel
tape recorders, jukeboxes ect.....
My thanks to the group for the suggestions. Lots of little screws but it
was worth it. Now, guess I will send in my Orion 1 for him to look at.
Greg
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Gary
Follett
Sent: Monday, March 14, 2016 11:53 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Orion 2
Check to see if you can control the sub receiver with the main receiver
encoder by selecting VFO A to control receiver two.
If this works, most likely the cable from the sub receiver encoder shook
loose in shipping.
Remove the 12 black flat head screws that hold the front panel assembly in
place and you should be able to see in there to see if the cable is off.
Gary
W0DVN
Sent from my iPad
> On Mar 14, 2016, at 4:46 PM, <gyates@dreamscape.com>
<gyates@dreamscape.com> wrote:
>
> Good Morning,
>
>
>
> I just got my Orion 2 back from repair and encoder for sub does not
> seem to work. I can enter frequency directly and receiver works. Any
> ideas of what I may be doing wrong or some magic button I have not pushed.
>
>
>
> Thanks,
>
>
>
> Greg
>
> WB2BIN
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2016.0.7497 / Virus Database: 4542/11815 - Release Date: 03/14/16
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2016.0.7497 / Virus Database: 4542/11819 - Release Date: 03/15/16
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|