Tnx Barry,
Andy, W3LI
________________________________________
From: TenTec <tentec-bounces@contesting.com> on behalf of Barry N1EU
<barry.n1eu@gmail.com>
Sent: Tuesday, March 15, 2016 1:50 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Orion 2
After Greg told me about them way back, I contacted them and subsequently
added them to the Wiki:
http://www.tentecwiki.org/doku.php?id=indy
73, Barry N1EU
On Tue, Mar 15, 2016 at 1:39 PM, P C Andy Anderson <xtraham58@hotmail.com>
wrote:
> Greg, do you have any contact information for Skyland Radio. Tried the
> web, no good. Phone, web site, email etc
>
> Tnx, Andy..W3LI
>
> ________________________________________
>
>
> Thanks for the suggestion on the cable. I took the Orion 2 apart and sure
> enough the cable to the sub was loose. Put it back on and so far it seems
> to work like new.
>
> Barry, as I discussed with you last year had a problem with the audio. I
> sent to Skyland Radio in Georgia while I was in Fl. They had it repaired
> and a few days and held it until I headed back to upstate NY. Radio
> arrived
> 1 day before me.
>
> Anyway, I have heard good reports on the company. Anyone interested google
> it and check out their facebook page. They work on things like reel to
> reel
> tape recorders, jukeboxes ect.....
>
> My thanks to the group for the suggestions. Lots of little screws but it
> was worth it. Now, guess I will send in my Orion 1 for him to look at.
>
> Greg
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Gary
> Follett
> Sent: Monday, March 14, 2016 11:53 AM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Orion 2
>
> Check to see if you can control the sub receiver with the main receiver
> encoder by selecting VFO A to control receiver two.
>
> If this works, most likely the cable from the sub receiver encoder shook
> loose in shipping.
>
> Remove the 12 black flat head screws that hold the front panel assembly in
> place and you should be able to see in there to see if the cable is off.
>
> Gary
>
> W0DVN
>
> Sent from my iPad
>
> > On Mar 14, 2016, at 4:46 PM, <gyates@dreamscape.com>
> <gyates@dreamscape.com> wrote:
> >
> > Good Morning,
> >
> >
> >
> > I just got my Orion 2 back from repair and encoder for sub does not
> > seem to work. I can enter frequency directly and receiver works. Any
> > ideas of what I may be doing wrong or some magic button I have not
> pushed.
> >
> >
> >
> > Thanks,
> >
> >
> >
> > Greg
> >
> > WB2BIN
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2016.0.7497 / Virus Database: 4542/11815 - Release Date: 03/14/16
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|