TenTec
[Top] [All Lists]

Re: [TenTec] Model 411 amp (aka Centaur)

To: tentec@contesting.com
Subject: Re: [TenTec] Model 411 amp (aka Centaur)
From: Al Gulseth <wb5jnc@centurytel.net>
Reply-to: wb5jnc@centurytel.net, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 26 Jan 2016 13:54:21 -0600
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Joe,

Just an ohms check may not be enough. You may be dealing with an intermittent 
breakdown under high voltage. A "hi-pot" (high potential) test with an 
insulation tester etc. would be the only way to know for sure. A winding 
layer to adjacent layer partial short in the HV side could also account for 
your symptoms, and might not be obvious because the winding resistance could 
show right at the low edge of the manufacturer's spec. (I went through that 
scenario years ago with a HV filter choke in a small AM BC transmitter.)

73 es GL, Al

On Tue January 26 2016 11:28:03 am Joe Papworth via TenTec wrote:
>    Thanks Andy. Was it the HV secondary that shorted?
>
>
>   I isolated the HV secondary from the HV board and it reads open to the
> frame and chassis. (Reads about 45 ohms when connected to the board)
>
>
>   Thanks, Joe, K8MP
>
>
>  -----Original Message-----
>  From: P C Andy Anderson &lt;xtraham58@hotmail.com&gt;
>  To: Discussion of Ten-Tec Equipment &lt;tentec@contesting.com&gt;
>  Sent: Tue, Jan 26, 2016 11:52 am
>  Subject: Re: [TenTec] Model 411 amp (aka Centaur)
>
>
>
>
>  Joe, I had a similar problem with my Centurion AMP.  It eventually failed
>  completely. The secondary of the power transformer shorted to the frame. I
> had the Xformer rewound at TRS.  BTW this transformer problem is a known.
>
>  73' Andy, W3LI
>
>  ________________________________________
>
>
>  Tuesday noontime, Joe:
>
>  I have a Centaur..............keep it covered when not in use.
>
>  My Elmer told me to always keep it covered..................dust is the
>  problem.
>
>  Even when covered, open it up every two-three years and do a internal
>  cleaning.
>
>  N1MHC/alsirois
>  =============
>
>
>
>  Gents,
>
>
>  Have any of you gone a few rounds with a Centaur amp?
>  I have a one that blows fuses very intermittently. It vaporizes them both,
>  simultaneously, so it's apparently a dead-short somewhere. This happens
> even in stand-by. (i.e. No key-down)
>
>
>  Before I tear into it, anyone have any ideas of common failures in these
>  amps?
>
>
>  Later, Joe, K8MP
>
>  _______________________________________________
>  TenTec mailing list
>  TenTec@contesting.com
>  http://lists.contesting.com/mailman/listinfo/tentec
>
>  _______________________________________________
>  TenTec mailing list
>  TenTec@contesting.com
>  http://lists.contesting.com/mailman/listinfo/tentec
>  _______________________________________________
>  TenTec mailing list
>  TenTec@contesting.com
>  http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>