Good luck Greg! This is the kind of image you're shooting for:
http://www.tentecwiki.org/lib/exe/fetch.php?cache=&media=orionpan3.jpg
Barry N1EU
On Thu, Dec 10, 2015 at 9:46 AM, Greg S via TenTec <tentec@contesting.com>
wrote:
> Thanks, Carl and Barry- just dipping my toes into the SDR/Panadapter stuff
> at this point. And I am working with an Eagle. I already purchased a used
> LP-Pan2, so once I have it up and running, will report results back to the
> group. (Going to try it with the factory supplied I.F. Output on the Eagle
> first, and take it from there). Again, thanks to the list!!!
>
> Greg, KC8HXO
> --------------------------------------------
> On Thu, 12/10/15, Carl Moreschi <n4py3@earthlink.net> wrote:
>
> Subject: Re: [TenTec] LP-Pan 2 on Orion 2
> To: tentec@contesting.com
> Date: Thursday, December 10, 2015, 9:40 AM
>
> In m opinion, it is much
> better to just use a separate SDR receiver such
> as SDRplay and have that run in parallel with
> the Orion. I have worked
> out excellent
> ways to share antenna connections between the Orion and
> SDR receivers.
>
> This method has none of the IF problems and
> even allows for the SDR
> receiver panadapter
> display to always follow the transmit frequency
> instead of the receive frequency.
>
> Carl Moreschi N4PY
> 58 Hogwood Rd
> Louisburg, NC
> 27549
> www.n4py.com
>
> On 12/10/2015 9:08 AM, Barry N1EU wrote:
> > no
> >
> > On Thu, Dec 10, 2015 at 9:07 AM, Greg S
> via TenTec<tentec@contesting.com>
> > wrote:
> >
> >> Barry.... Will the Lp-pan2 with amp
> built in take care of the discrepancy
> >> you note? Thanks! Greg, KC8HXO
> >>
> >> Sent from
> Yahoo Mail on Android
> >>
> >> On Thu, Dec 10, 2015 at 7:24,
> Barry N1EU<barry.n1eu@gmail.com>
> wrote:
> >> I found the
> RX366 IF output resulted in a poor panadapter trace and
> posted
> >> that to this reflector and
> tentecwiki.org - use the VE7TK mod with Clifton
> >> Labs buffer amp. I suspect the Eagle
> IF output is no better than the RX366
> >> and also really needs the mod, since
> it's essentially the same receiver.
> >>
> >> I just
> plugged it into my motherboard soundcard, a RealTek HD or
> something
> >> like that. It works
> fine, as do the soundcards recommended on
> >> telepostinc.com
> >>
> >> Barry N1EU
> >>
> >> On Wed, Dec
> 9, 2015 at 11:10 PM, Kim Elmore<cw_de_n5op@sbcglobal.net>
> >> wrote:
> >>
> >>> Somewhere in the archives,
> I've read that the way the RX-366 IF output is
> >>> set up creates some undesirable
> dips and peaks in it.
> >>>
> >>> Kim N5OP
>
> -----------------------------SNIPPED--------------------------------
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|
