I have an Omni 6 meter, same meter.
Gary
> On Oct 30, 2015, at 5:10 PM, John King via TenTec <tentec@contesting.com>
> wrote:
>
> Do you still have the Paragon's S meter ?
>
> On Thursday, October 29, 2015 1:08 PM, Rodney <w3krq@dejazzd.com> wrote:
>
>
> I still have this complete with 14 relays for sale these relays are surface
> mount. This would be good insurance at 110.00 when it cost 110.00 labor at
> TenTec.
>
> -----Original Message-----
> From: Rodney
> Sent: Saturday, October 24, 2015 5:32 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Relays for a Paragon. Hopefully......
>
> I have a low pass board for a Ten Tec Eagle . I though I needed a relay
> found out the trouble was on the tuner board. I now have a complete board
> for the Eagle if I had sent the Eagle down for repairs it would have cost me
> shipping and 110.00 for labor plus parts, It cost me 190.00 for the board, I
> no longer have the Eagle so I am selling the low pass board for 140.00
> shipped.
>
> -----Original Message-----
> From: Wade Staggs
> Sent: Saturday, October 24, 2015 5:17 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Relays for a Paragon. Hopefully......
>
> *Thanks Peter,*
> * If we can't get OEM? My plan will now be to
> replace them all. And thanks again for the advise.*
> * 73 from Wade/KJ4WS*
>
> On Sat, Oct 24, 2015 at 3:56 PM, Peter Frenning [OZ1PIF] <peter@frenning.dk>
> wrote:
>
>> Den 24-10-2015 kl. 21:57 skrev Wade Staggs:
>>
>>> *Paul, at Ten Tec says that the Relays for the Low Pass Filter Board for
>>> the Paragon, are no longer available. Written on the white body of the
>>> relay is Wabash and the part # on the relay is 1925-3-2 ...... I am
>>> finding
>>> them pretty Unobtainium from all of my usual sources also. Does anyone
>>> have
>>> a decommissioned Paragon with a good Low Pass Filter Board? Or any spares
>>> of this relay? We have found some Wabash Reed Relays that are a perfect
>>> Sub. Exact Pin Out and Dimensions. The relays we found do the exact same
>>> job in a Collins KWM-380. I just hate to use Non OEM Parts, no matter how
>>> close the match is.*
>>> * 73 to All from
>>> Wade/KJ4WS*
>>>
>>> Please note, if you have to go the second source route, that you have to
>> pair the relays so that a given band will be using to identical relays,
>> (same close/open characteristics and current consumption).
>>
>> Several years ago, while I still owner my Paragon, I had to go that route,
>> and Paul at TT stressed the point to me (was also very helpful with
>> obtaining alternative relays)
>>
>> --
>> Vy 73 de OZ1PIF/5Q2M, Peter
>>
>> ******************************************
>> ** If it sounds too good to be true -- **
>> ** it is! **
>> ** If it sounds about right -- make **
>> ** sure you can afford to be wrong! **
>> ** **
>> ** -- Robert Heinlein: **
>> ** "Time enough for love" **
>> ******************************************
>> email: peter(no-spam filler)@frenning.dk
>> http://www.frenning.dk/oz1pif.htm
>> Ph. +45 4619 3239/ +45 2332 9464
>> Snailmail:
>> Peter Frenning
>> Ternevej 23
>> DK-4130 Viby Sj.
>> Denmark
>> ******************************************
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
>
> --
> *Living one day at a time with Jesus as my Savior. But, still having Fun.*
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|