John,
First, when you speak of the Eagle INI file, are you referring to the file
you have created? I have never seen an Eagle file in OmniRig.
I have never changed anything in the INI file.
I have always worked with the stock Orion INI file.
I attempted to add a BW=0 command to the Orion INI file, and after that it
did not work at all, so I scrapped it and just used the stock file.
All we need is for the software to release command of the BW, so it will
automatically revert back to the radio's knob. That fixes that problem.
I need to bet BandMaster running.
I have just swapped computers, and put a more powerful computer in the
station, but now I have to install all the software new.
73 - Rick, DJ0IP
(Nr. Frankfurt am Main)
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of John Henry
Sent: Monday, July 28, 2014 6:15 PM
To: Discussion of Ten-Tec Equipment
Subject: [TenTec] BW and Eagle
uh, before we go too far down the road, am I missing something?
I don't see a bandwidth control available in OmniRig ....
Here is the list:
pmFreq operating frequency
pmFreqA VFO A frequency
pmFreqB VFO B frequency
pmPitch CW pitch frequency
pmRitOffset RIT offset frequency
pmRit0 Clear RIT - this is a write-only parameter
pmVfoAA receive and transmit on VFO A
pmVfoAB receive on VFO A, transmit on VFO B
pmVfoBA receive on VFO B, transmit on VFO A
pmVfoBB receive and transmit on VFO B
pmVfoA receive on VFO A, transmit VFO unknown
pmVfoB receive on VFO B, transmit VFO unknown
pmVfoEqual copy the frequency of the receive VFO to the transmit
VFO
pmVfoSwap swap frequencies of the receive and transmit VFO's
pmSplitOn enable split operation
pmSplitOff disable split operation
pmRitOn enable RIT
pmRitOff disable RIT
pmXitOn enable XIT
pmXitOff disable XIT
pmRx enable receive mode
pmTx enable transmit mode
pmCW_U CW mode, upper sideband
pmCW_L CW mode, lower sideband
pmSSB_U USB mode
pmSSB_L LSB mode
pmDIG_U Digital mode (RTTY, FSK, etc.), upper sideband
pmDIG_L Digital mode, lower sideband
pmAM AM mode
pmFM FM mode
Am I misinterpreting one?
Rick, which one did you use to change the BW in OmniRig INI file?
There is an RIT Offset in the Orion .ini, but, no BW or PBT????
Maybe I'm done? (once I settle the mode change issue)
ok, confused here.
When I use the Orion ini file, with an Orion, I don't see it change modes or
bandwidth. It changes modes when I tell it to in BandMaster. Seems to be
working right. Modes work, split works, VFOA and VFOB are changed correctly
with bandmaster, and bandmaster follows the rig. So I don't see any problems
with the Orion file with my Orion here.
Please re-iterate the problem so I can test again.
When I run the Eagle with the Eagle.ini file, it changes modes when I ask it
to, split works, VFOA and VFOB are chagned correctly with bandmaster, and
bandmaster follows the rig.
So, I think I might be done, no?
When just running Win-Test, it does do some things different, e.g. it does
force the mode to USB on several band changes, not sure why.
On the Eagle, it never sends a bandwidth command, so bandwidth on the Eagle
is always changeable on the Eagle front panel. Never changes via CAT. I
don't see a command for it.
Thanks, and 73,
John Henry, KI4JPL
TEN-TEC Engineering, a Division of RFConcepts LLC
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|