Re: [TenTec] Invoking OM7 500 Hz filter ?

["Bob McGraw - K4TAX" <RMcGraw@Blomand.net>]

There is no front panel IF Filter manual selection available.

Filter selection is either automatic, thus following the DSP BW when I-F 
FILTER is set to AUTO.
You can select the filter manually via the MENU on the I-F FILTER line.  The 
Multi knob makes this choice from the MENU as it steps through all the 
filter choices.
73
Bob, K4TAX


----- Original Message ----- 
From: <bcarling@cfl.rr.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Thursday, July 10, 2014 7:28 PM
Subject: Re: [TenTec] Invoking OM7 500 Hz filter ?


> Thank you. Yes, I read that, and tried it. However, it does not tell me 
> how to select them and
> it didn't switch.
>
> What do I rotate or switch?
>
> Is there any way to customize buttons on the front panel to make one of 
> them select this filter
> without going through the menu every time?
>
> On 10 Jul 2014 at 19:25, Bob McGraw - K4TAX wrote:
>
> > The I-F FILTER line in the MENU will allow you to switch the filter of 
> > your
> > choice manually.
> >
> > 73
> > Bob, K4TAX
> >
> >
> > ----- Original Message ----- 
> > From: <bcarling@cfl.rr.com>
> > To: <tentec@contesting.com>
> > Sent: Thursday, July 10, 2014 7:17 PM
> > Subject: Re: [TenTec] Invoking OM7 500 Hz filter ?
> >
> >
> > > Thank you Bob. I already did all that. And yes, it is already set to
> > > AUTIO.
> > >
> > > I simply want to know how to switch it on and off when I am operating 
> > > the
> > > radio. I thought I
> > > made that clear.
> > >
> > > "Does anyone know how to invoke the 500 Hz Collins filter once it is
> > > installed and enabled?"
> > >
> > >
> > > On 10 Jul 2014 at 19:06, Bob McGraw - K4TAX wrote:
> > >
> > >> Go to the MENU. Scroll to the bottom.  Set ENABLE 500 Hz to YES.  And 
> > >> if
> > >> you
> > >> have the 300 Hz filter do the same for that one.  Then at the line I-F
> > >> FILTER select AUTO.
> > >>
> > >> 73
> > >> Bob, K4TAX
> > >>
> > >>
> > >> ----- Original Message ----- 
> > >> From: <bcarling@cfl.rr.com>
> > >> To: <tentec@contesting.com>
> > >> Sent: Thursday, July 10, 2014 6:42 PM
> > >> Subject: [TenTec] Invoking OM7 500 Hz filter ?
> > >>
> > >>
> > >> > Hello,
> > >> >
> > >> > I now have a clean sounding OMNI VII after doing a master reset. 
> > >> > Thanks
> > >> > guys.
> > >> >
> > >> > Does anyone know how to invoke the 500 Hz Collins filter once it is
> > >> > installed and enabled?
> > >> >
> > >> > I have read the manual through twice and still can't figure out how 
> > >> > to
> > >> > switch from 2.5 kHz
> > >> > filter to 500 Hz !!  Maybe I am not too smart. The book seems to 
> > >> > dance
> > >> > all
> > >> > around the topic
> > >> > but never tell you how!
> > >> >
> > >> > 73 - Brian, AF4K
> > >> >
> > >> > Brian Carling, Radio AF4K
> > >> > _______________________________________________
> > >> > TenTec mailing list
> > >> > TenTec@contesting.com
> > >> > http://lists.contesting.com/mailman/listinfo/tentec
> > >> >
> > >>
> > >>
> > >
> > >
> > > Brian Carling, Radio AF4K
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec