Tony, see u Sunday. BTW, tnx for relaying Kathy, WB2IWM in from time to time.
Andy
>
>
> In that aspect I guess you're right. I too will save my money for the next
> TT rig that turns my fancy. I have my O-II now since 2007 and never had a
> spot of trouble with it. Oh oh, just jinkst it, knock on Wood.
>
> Tony VE3DWI.
>
> Sent from my BlackBerry 10 smartphone on the Bell network.
> Original Message
> From: P C A
> Sent: Tuesday, May 13, 2014 17:41
> To: TenTec@contesting.com
> Reply To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] RX366 9 MHz Out
>
> Tony, It is a fine radio, you hear me on it every week end. However, I choose
> not to spend any more money on it.
> Andy, W3LI
>
> >
> >
> > Just because they are out of production doesn't mean it's obsolete Andy.
> > It is still my most favorite rig and, hopefully, will last me a long time.
> >
> > Tony VE3DWI.
> >
> >
> >
> > Sent from my BlackBerry 10 smartphone on the Bell network.
> > Original Message
> > From: P C A
> > Sent: Tuesday, May 13, 2014 17:12
> > To: TenTec@contesting.com
> > Reply To: Discussion of Ten-Tec Equipment
> > Subject: Re: [TenTec] RX366 9 MHz Out
> >
> > Kim, can not understand why you would spend the money on a dead horse. The
> > Oll is obsolete, I know I own one.Andy, W3LI
> >
> > >
> > >
> > > Kim, FYI I posted to this list about my lack of success using the RX366
> > > 9MHz output to drive LP-PAN (w preamp). I believe the VE7TK mod that adds
> > > a Clifton Labs buffer amp to generate the 9MHz output will probably yield
> > > much more satisfactory results.
> > >
> > > 73/GL,
> > > Barry N1EU
> > >
> > >
> > > On Tue, May 13, 2014 at 1:36 AM, Kim Elmore
> > > <cw_de_n5op@sbcglobal.net>wrote:
> > >
> > > > I've just finished the installation of my new (and, apparently last)
> > > > RX366
> > > > into my Orion II. Being the kind of ham that wants to have all the bells
> > > > and whistles available, even if I don't have the ability to use them
> > > > right
> > > > now, I decided to go ahead and take advantage low-level the 9 MHz output
> > > > from the RX366. I obtained a length of coax with TMP connectors on both
> > > > ends and looked up the 9 MHz output mod by VE7TK. To my astonishment, I
> > > > see
> > > > that one of the unused TMP receptacles on the back of the unit (the one
> > > > next to where cable 3 plugs in) goes to the RCA jack on the back
> > > > labelled
> > > > "SPARE." I double checked and, sure enough, there's a DC path to the
> > > > "SPACE" RCA jack on the back. KEWL!
> > > >
> > > > So, apparently, all I need now is an LP PAN adapter unit with a preamp
> > > > and
> > > > I'll be cookin' with a real-time spectrum display.
> > > >
> > > > Kim N5OP
> > > >
> > > >
> > > > _______________________________________________
> > > > TenTec mailing list
> > > > TenTec@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/tentec
> > > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|