James, that is just for a few multipliers.
You don't point it south and call for hours.
The masses of the participants are in USA, Europe, and Japan.
You have you beam pointed in those directions most of the time.
73
Rick, DJ0IP
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Richards
Sent: Friday, June 21, 2013 9:50 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] RF Speech Processor "TX IMD"
It is a little different here in Michigan... we can work South America and
Africa along grey line during at least part of the contest, so aiming the
beam due south is a good idea.
I think SA stations are fun to work because they tend to be very friendly,
and willing to work hard to complete the contact, despite difficult
conditions. Maybe the skip zones don't work for guys who reside South of
us, so it may not work the same for everybody.
------------------- K8JHR --------------------
On 6/21/2013 2:55 AM, Rick - DJ0IP / NJ0IP wrote:
> Kim, you may have just come up with a great concept for planning a
> contest radio station.
> "Always live south of your competitors".
> It's the same over here too, we almost never point the beam south.
> You work an occasional multi to the south, but then you point the beam
> back to the NE or NW where the action is.
>
> 73
> Rick, DJ0IP
>
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Kim
> Elmore
> Sent: Friday, June 21, 2013 5:19 AM
> To: Rick - DJ0IP / NJ0IP
> Cc: 'Discussion of Ten-Tec Equipment'
> Subject: Re: [TenTec] RF Speech Processor "TX IMD"
>
> Sorry for the delayed response.
>
> Yep, I misunderstood: no amount of filtering on a rx will fix a poor tx.
> Nothing can be done about transmitted phase noise or poor IMD of a tx
> once it leaves the tx.
>
> I was reminiscing about K0RF back in the late 80's/early 90's when he
> was running a TS-930S. That was about as good as anything got back then.
> We certainly have much better, now. He has truly fantastic antenna
> array and full QRO Alpha amps (or did back then) and when he was
> pointed at me, about
> 10 mi south, all I could do was switch bands. Fortunately, he wasn't
> compelled to do that very often in a contest simply because a lot of
> mults are in other directions.
>
> Kim N5OP
>
>
> On 6/18/2013 3:12 PM, Rick - DJ0IP / NJ0IP wrote:
>> Reply No. 2 on this, Kim...
>>
>> I thought K0RF was now running an FT-5000 in class A mode, driving a
>> very good linear.
>> As such, I assume you are speaking historically.
>> You shouldn't have any problems with him anymore.
>>
>> 73
>> Rick, DJ0IP
>>
>> -----Original Message-----
>> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
>> Kimberly Elmore
>> Sent: Tuesday, June 18, 2013 6:27 PM
>> To: Discussion of Ten-Tec Equipment
>> Subject: Re: [TenTec] RF Speech Processor "TX IMD"
>>
>> Yes, indeed: the introduction the PLL lead to wonderful flexibility
>> in frequency coverage and generation along with mounds of phase noise.
>> The phase noise has been largely corralled, but not IMD. I wonder:
>> what IMD level is good enough? Something around -40 dB seems
>> considered
> insufficient.
>> Would -50 dB do it? -60 dB? What things affect the linearity and
>> transfer function of a PA? Can IMD be "designed out" of a PA, or is
>> it fundamentally caused by the transfer function inherent in the
>> active, amplifying device (transistor or tube) itself? I honestly don't
know.
>>
>> Oh, and when I heard K0RF's phase noise, I was about 10 mi from him
>> :)
>>
>> I will take issue with one aspect, though: band pass filters on the
>> output of a transmitter can most certainly attenuate phase noise, or
>> any other emitted RF, that falls outside the filter's pass band.
>> Phase noise is Gaussian (white) in nature and we can turn white noise
>> into anything we want with proper filtering. There's nothing special
>> about phase noise or nth-order IMD products in this regard: band pass
>> filters pass only what's in the pass band (the ultimately tautology!).
>> The pass band may be, say, the entire 20 m band plus a bit for
>> safety, but a good filter will stop anything outside of the pass
>> band. So, a transmitter with a good band pass filter on it won;t much
>> affect any other
> band but 20 m.
>>
>> I'll take my '930S out again this year and double check its noise
>> generation as I know darn good and well that it makes some. I'll even
>> try it on 'phone to see how much trash it makes because I really
>> don't have any idea right now. No, I don't don't own the proper
>> equipment, such as a spectrum analyzer, to allow me to measure it. I
>> suppose that makes me an inadequate ham in some eyes (hangs head in
shame).
>>
>> Kim N5OP
>>
>>
>> ________________________________
>> From: Rick - DJ0IP / NJ0IP <Rick@DJ0IP.de>
>> To: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
>> Sent: Tuesday, June 18, 2013 10:03 AM
>> Subject: Re: [TenTec] RF Speech Processor "TX IMD"
>>
>>
>> Guys, this is EXACTLY what I have been talking about.
>>
>> BROADBAND PHASE NOISE - not just the 3rd order IMD.
>> This noise is not just wide, it's across the entire spectrum.
>>
>> Now hang a 1.5KW linear amp on one of those!
>> You don't just bother others on your block, you bother those within a
>> couple of miles.
>>
>> But of course some of the rigs are also pathetic on the higher order IMD.
>> NONE are as good as a 1960s Collins 30S-3.
>>
>> (OK, sure the FT-5000 is if you run it at 75w in class A, but as soon
>> as you turn on the speech processor, it's hosed too!)
>>
>> Nearly 50 years, not only have we seen no progress, the IMD has
>> gotten worse.
>>
>> 73
>> Rick, DJ0IP
>>
>>
>> -----Original Message-----
>> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
>> Duane Calvin
>> Sent: Tuesday, June 18, 2013 4:49 PM
>> To: 'Discussion of Ten-Tec Equipment'
>> Subject: Re: [TenTec] RF Speech Processor "TX IMD"
>>
>> Same with the TS-430. I have a neighbor less than 500' away running
>> CW all the time. When he had his TS-430 he covered a major portion
>> of the band he was on with transmitted phase noise. It was a pure
>> delight when he up graded to a TS-570 a few years ago and then I
>> couldn't hear him until I was within 5-10 KHz of him or so.
>>
>> 73, Duane
>>
>> Duane Calvin, AC5AA
>> Austin, Texas
>> www.ac5aa.com
>>
>>
>>
>>
>> -----Original Message-----
>> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
>> Barry N1EU
>> Sent: Tuesday, June 18, 2013 9:41 AM
>> To: Discussion of Ten-Tec Equipment
>> Subject: Re: [TenTec] RF Speech Processor "TX IMD"
>>
>> On Tue, Jun 18, 2013 at 1:16 AM, Kim Elmore
> <cw_de_n5op@sbcglobal.net>wrote:
>>
>>> All that said, I never tried phone with it at FD but I'll give it a
>>> shot this year as a quick test to see if the IMD wipes out everyone
else.
>>>
>>>
>> We use a TS930S on ssb every year at Field Day and it just wipes out
>> the rig that's down in the cw portion of the same band due to phase
noise.
>>
>> Barry N1EU
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|