John,
I don't have a true peak-reading wattmeter, so I can't measure the PEP
output. Jim may be right about controlled-carrier; I can't tell. When using
TUNE and PWR, I get 95 watts, but only 11 watts with PTT and no speech.
73 Ray
In a message dated 6/11/2010 7:01:47 P.M. GMT Standard Time,
wb4qda@yahoo.com writes:
Ray
When I speak into the Micrphone with the mode set to AM ,I modulates up
to 80 watts .Tune is 21 watts and tune then the PWR I get 95 watts output.
73
John
----- Original Message ----
From: "Rsoifer@aol.com" <Rsoifer@aol.com>
To: tentec@contesting.com
Sent: Fri, June 11, 2010 10:38:22 AM
Subject: Re: [TenTec] Orion 2 Firmware 2.044A Released
John,
Funny thing about that. With the mode set to AM, when I hit Tune and
then
Pwr I get full output like you did, but if I hit the PTT button instead,
all I get is 11 watts on the Bird. It worked fine with 2.041XT.
73 Ray
In a message dated 6/11/2010 3:22:43 P.M. GMT Standard Time,
wb4qda@yahoo.com writes:
Ray
I just tested my O2 on AM max output was 80 warrs on an Alpha watt meter
also about the same reading on a LP-100A watt meter with the Power set to
100%
using the new fearmware version 2.044A
73
John wb4qda
----- Original Message ----
From: "Rsoifer@aol.com" <Rsoifer@aol.com>
To: ronc@sonic.net; w5pny@arrl.net; tentec@contesting.com
Sent: Fri, June 11, 2010 8:36:18 AM
Subject: Re: [TenTec] Orion 2 Firmware 2.044A Released
Ron,
The NR problem has been fixed (!) but the old low-output problem on AM is
back. Mine measures 11 watts carrier power, max. It worked fine with
2.041XT.
73 Ray W2RS
In a message dated 6/11/2010 2:17:05 A.M. GMT Standard Time,
ronc@sonic.net
writes:
I have adjusted the "Wish List" for the Orion II to reflect the newest
version of the firmware. It's at www.N6IE.com
Ron N6IE
www.N6IE.com
----- Original Message -----
From: "Harry G McGavran Jr" <w5pny@arrl.net>
To: <tentec@contesting.com>
Sent: Thursday, June 10, 2010 5:50 PM
Subject: Re: [TenTec] Orion 2 Firmware 2.044A Released
>
> With this one I can set the side-tone level all the way
> up to 65 before the pops begin, and by the time one
> gets past 80 on towards 99 the distortion on the
> side-tone is still really bad -- BUT -- for me at
> least, levels are 50-60 are all I need and that is
> now distortion free, at least with a 610 Hz sidetone
> which is the only one I tested or use. I also am
> using the speaker and not headphones for this.
> Since one gets the side-tone every time the SPOT
> button is used, the side-tone distortion was really
> objectionable with 2.043B.
>
> The NR seems better too, but most all the time I don't
> really need it -- and it's nice not to have artifacts that
> sound like NR action on the side-tone which the side-tone
> is set to 50-60.
>
> There are a few CAT wierdnesses here and there, but the reliability
> of sending a strings of "*" commands seems better.
>
> Unless something else crops up, I think I can live with this
> release...
>
> 73 --
>
> Harry, W5PNY
>
>
>
>
>
> --
>
> Harry G. McGavran, Jr.
>
> E-mail: w5pny@arrl.net
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|