i had somewhat low output (voice peaks) on my paragon with a shure 444d mic -
although audio reports were always excellent - when i switched to a ten tec
mike the voice peaks went through the roof and now i am completely satisfied -
i can see you are already using a ten tec mic - have you tried a different one?
thx, john> From: d.e.warnick@comcast.net> To: tentec@contesting.com> Date: Mon,
4 Feb 2008 19:15:15 +0000> Subject: Re: [TenTec] 705 Mic Low Output Help
Request> > My 705 microphone manual shows pin 4 as Plus Electret Voltage (7 to
14) VDC).> > My Omni VI+ manuas shows the transciever supplying +4 volts to the
mic, although no-load measurement at the mic connector shows 9.44 volts using a
Fluke 77 multimeter.> > The only modification shown in the 705 manual is to a
Corsair Transciever.> > I hope this helps. Also, at the risk of sounding like a
broken record, I cannot overemphasize the value of manuals for all your TenTec
gear. The absolute best first source for this information is TenTec. Their tech
line is also the best if you need help> > Dave> WA3MKB> -------------- Original
message -------------- > From: "David & Chris Drake" <drakes@psci.net> > > >
Don't remember for sure without looking it up. But I think 9-12v. The mic > >
runs off a 9v battery if not getting power dir
ectly, so it would make sense > > it needs around 9v to work. > > David > > >
> -----Original Message----- > > From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com] > > On Behalf Of Greg Kuczek > > Sent:
Monday, February 04, 2008 9:15 AM > > To: Discussion of Ten-Tec Equipment > >
Subject: Re: [TenTec] 705 Mic Low Output Help Request > > > > > > I'm running
it thru the jack. I haven't checked the voltage at the jack yet, > > thanks. Do
you know what the voltage should be? > > > > 73 > > Greg W9VOX > > > > David &
Chris Drake wrote: > > Are you running the 705 by battery or through the Omni
V? If through the > > Omni V, check the voltage at the jack first. If by
battery, check the > > battery. Then check the plug before going inside it. > >
Good luck, > > David > > > > ----- Original Message ----- > > From: "Greg
Kuczek" > > To: > > Sent: Sunday, February 03, 2008 10:23 PM > > Subject:
[TenTec] 705 Mic Low Output Help Request > > > > > > >I have a 705 mic
that I am having low output problems when used with an > > >Omni V. I've read
that you can change out the R11 resisitor to 3300 ohms to > > > > >help correct
this. Unfortunately I don't have a schematic or any > > >documentation to help
me locate this resistor. Any help identifying R11 > > >would be appreciated. >
> > > > > 73 de Greg W9VOX _______________________________________________ > >
> TenTec mailing list > > > TenTec@contesting.com > > >
http://lists.contesting.com/mailman/listinfo/tentec > > > > > > > > > > > >
_______________________________________________ > > TenTec mailing list > >
TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec > > >
> _______________________________________________ > > TenTec mailing list > >
TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec > > >
> > > _______________________________________________ > > TenTec mailing list >
> TenTec@contesting.com > > http://lists.contesting.com/mailman/lis
tinfo/tentec > _______________________________________________> TenTec mailing
list> TenTec@contesting.com> http://lists.contesting.com/mailman/listinfo/tentec
_________________________________________________________________
Shed those extra pounds with MSN and The Biggest Loser!
http://biggestloser.msn.com/
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|