Carl,
This is also done well in other rigs, and I (along with others,
probably) have requested the "Quick QSX" function in the Orion. It would be
easy - long press of the A>B button could copy A->B, perform whatever offset
has been preselected by the user (i.e., +5 for SSB, +1 for CW, +1 for FSK,
etc.) and switch TX to VFO-B. Gary responded to me a couple of years ago
that this sounded like a great option to him, but it never went any further.
I guess it got bumped in favor of other projects. There is no reason this
should need additional software to do since it is standard on many
competitive rigs, although it's great that you have provided it!
73, Duane
Duane Calvin, AC5AA
Austin, Texas
www.ac5aa.com
-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of Carl Moreschi
Sent: Thursday, March 08, 2007 11:27 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] OmniVII band output info??
It's just that there's so many thing that computer programs such as mine can
make simple and fast. Like when trying to call a DX station and suddenly he
announces he is listening up 5. All I have to do is press my "up" key
followed by the "5" key. That makes my VFO B by 5 khz above my VFO A and
turns on split. All in one operation. I am almost always the first to call
when this happens. Or when I change bands everything gets restored to the
last values I had on that band even things like power output settings,
antenna settings, attenuators, preamps, and so on. And it's great to have
separate band register buttons by mode. I have a full set for CW, another
set for SSB, and a third set that can be defined for SWL bands or RTTY
sub-bands.
Carl Moreschi N4PY
121 Little Bell Drive
Bell Mountain
Hays, North Carolina 28635
----- Original Message -----
From: "Dale Martin" <kg5u@hal-pc.org>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Thursday, March 08, 2007 11:59 AM
Subject: Re: [TenTec] OmniVII band output info??
>
>
> That's too bad....not you and your software, Carl, but the fact that the
> band data is not available on the back of the radio.
>
> Forgive me if I sound a but retro here, but.....
>
> I think I will stay with my Omni VI's where my radios control the antenna
> switching and bandpass filters.....without having to have the computer
> turned on.
>
>
> 73,
> Dale, kg5u
>
> >
> > There are no band outputs on the back of the Omni VII.
> > Computer control is the answer. My N4PY software will have
> > full function for this.
> >
> >
> > Carl Moreschi N4PY
> > 121 Little Bell Drive
> > Bell Mountain
> > Hays, North Carolina 28635
> >
> > ----- Original Message -----
> > From: <k7gt@charter.net>
> > To: <tentec@contesting.com>
> > Sent: Thursday, March 08, 2007 11:22 AM
> > Subject: [TenTec] OmniVII band output info??
> >
> >
> > > Hi gang,
> > >
> > > A question for those with OmniVIIs. I reviewed briefly the OmniVII
> > > manual
> > that is
> > > on-line and couldn't locate an output for band information. Both the
> > OmniVI and Orion
> > > have that info available on the back panel (so did the
> > Corsair I and
> > > some
> > earlier rigs).
> > > Has this very useful feature been dropped or does one have to go
> > > through
> > computer
> > > control to get that info?
> > >
> > > Otherwise it looks like the VII may be in my future.
> > >
> > > Allan K7GT
> > >
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|