TenTec
[Top] [All Lists]

Re: [TenTec] ORION Display (horizontal line??)

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] ORION Display (horizontal line??)
From: "Rich McCabe" <r.mccabe@ctiowa.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 22 Jan 2007 21:32:56 -0600
List-post: <mailto:tentec@contesting.com>
I look forward to the day when Ten Tec has the talent/desire to create a
better interface. They have the radio fundamental part down pat, but the
interface is a major let down for me after having a Pro III. The fact they
are using a low resolution display doesn't help either.

So basically, I find those little filter boxes useless too. The scope is
next in line !

73,

Rich
Kd0zv



-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of mcelmer1
Sent: Monday, January 22 9:01 PM
To: Ron Castro; Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] ORION Display (horizontal line??)

I'm an Orion 1 owner and still can't figure out what in the hell these 
rectangles are. And the manual is totally useless. I suppose I'm to read the

mind of the designer to divine what the rectangles represent.
----- Original Message ----- 
From: "Ron Castro" <ronc@sonic.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, January 22, 2007 7:37 PM
Subject: Re: [TenTec] ORION Display (horizontal line??)


> That is the line I assumed Bernie was referring to also, and it still
> remains a mystery!  I am sitting here trying to change it, and sometimes 
> and
> can and then, I can't make it change again.  It looks like it is somehow
> associated with the BW setting, but appears to work only intermittently.
>
> Just so everyone is clear where it is, the line is below the filter BW
> graphic rectangle and is a one pixel horizontal  line located one pixel
> immediately above the upper border of the rectangle enclosing the 
> frequency
> calibrations of the sweep box.
>
>      Ron N6IE
> www.N6IE.com
> (Formerly N6AHA)
>
> ----- Original Message ----- 
> From: "Richard Williams" <richardw@mho.com>
> To: <w1ael@arrl.net>; "Discussion of Ten-Tec Equipment"
> <tentec@contesting.com>
> Sent: Monday, January 22, 2007 5:47 PM
> Subject: Re: [TenTec] ORION Display (horizontal line??)
>
>
>> Allen,
>>
>> The way I read Bernie's question, he is asking about the thicker solid
>> line
>> that is directly above the spectrum display.   There is a "break" (it
>> becomes a thin line) in it just between the "0" and the next number (.6,
>> 1.2, 2.5, 5, or 10 - depending on the sweep range) to the left.
>>
>> I read it this way because Bernie says:  "Immediately above the spectrum
>> sweep scope is a horizontal line on which the rectangles representing the
>> bandpasses for the main (left) and sub (right)  receivers rest".   The
>> rectangles don't "rest" on the the horizontal line(s) above the filter
>> bandwidth graphic; which you  correctly defined in your response.
>>
>> Personally, I don't know what the break in the bar represents;
>> interesting
>> question,  do you happen to know the answer?
>>
>> Dick K8ZTT
>>
>>
>> ----- Original Message ----- 
>> From: "Allan H. Kaplan" <w1ael@arrl.net>
>> To: <tentec@contesting.com>
>> Sent: Monday, January 22, 2007 6:14 PM
>> Subject: Re: [TenTec] ORION Display
>>
>>
>>> The horizontal line above the filter bandwidth graphic represents the
>>> bandwidth of the roofing filter in use at 9 MHz.  The filter bandwidth
>>> graphically represents the ultimate selectivity implemented by the
>>> BANDWIDTH control in the DSP IF and the (wider) roofing filter gets
>>> selected automatically based on the BW control.  Hope this helps. 73,
>>> Allan, W1AEL in Sevierville, TN.
>>>
>>> ----- Original Message ----- 
>>> From: <K5XS@aol.com>
>>> To: <tentec@contesting.com>
>>> Sent: Saturday, January 20, 2007 8:14 AM
>>> Subject: [TenTec] O-2 Screen Lines
>>>
>>>
>>>
>>>> > This is truly fun.  I am figuring out the radio and trying to 
>>>> > discover
>>>> > every
>>>> > little nook and cranny on it.
>>>> >
>>>> > One thing has me puzzled, and I can't find it in the manual.
>>>> >
>>>> > Immediately above the spectrum sweep scope is a horizontal line on
>>>> > which
>>>> > the
>>>> > rectangles representing the bandpasses for the main (left) and sub
>>>> > (right)
>>>> > receivers rest.  The line has a break in it, and it is decidedly off
>>>> > center
>>>> > (to the lest a bit).
>>>> >
>>>> > Does that line represent something?  Does the break represent
>>>> > something?
>>>> >
>>>> > Thanks
>>>> >
>>>> > Bernie K5XS
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>