TenTec
[Top] [All Lists]

Re: [TenTec] Orion Aux Audio output (explained)

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Orion Aux Audio output (explained)
From: <wn3vaw@verizon.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 28 Mar 2006 12:41:55 -0600 (CST)
List-post: <mailto:tentec@contesting.com>
Mike, once I got done chuckling, I figured I'd pass on a similar tale... a 
little OT, but still...

I once worked at the State College remote studio for the old WGMR-FM 
Tyrone/State College.  The chief engineer who worked at the studio was and 
old-fashioned kinda guy, very set in his ways... and didn't believe in 
grounding.  Just didn't believe it was neccesary!  Waste of time!

Well, for a long time, if someone was recording commercials in the late 
morning, afternoon, or evening, I noticed on playback that you sometimes heard 
a voice or CW in the background.  Of course, I immediately recognized the 
source of the background noise, since I was an alumni of the Penn State ARC; 
K3CR sat about, oh, 100 yards or so on the other side of West College Avenue 
from the studio.  So if someone was in the shack working DX or a traffic net or 
ragchewing at the same time the commercials were being recorded...

The CE's response?  He was all set to complain to the FCC and Penn State and 
have "those kids!" thrown off the air and out of school.  Until I also pointed 
out to him that we were sometimes picking up the State College police, Alpha 
Fire, the 146.74 K3HKK/R repeater, even my 1 W Wilson 1402 HT.  

He still didn't believe it was "his" studio at fault, until just to humor me, 
he grounded everything.  Problem went away.  Imagine that.

And FWIW, this is the same guy who helped build the original WBLF-AM studio in 
Bellefonte PA.  In a converted apartment.  He always claimed the original 
transmitter remote controls were located in the bathroom... specifically, in 
the tub & shower.  Supposedly, when the FCC people came to inspect the station 
before it went on the air, they took one look at THIS setup and broke up 
laughing (and worse).  I heard THAT tale from a number of people, and I don't 
know if it's actually true -- but if it's not, it should be!

73, ron wn3vaw

---------------------------------------------------
From: Mike Gorniak <mgorniak@genesiswireless.us>
Date: Tue Mar 28 12:07:30 CST 2006
To: tentec@contesting.com
Subject: Re: [TenTec] Orion Aux Audio output (explained)

Larry, I agree with you in principle. However, I must add an anecdote that 
illustrates the problem in the real world:

I once worked for a radio station that had a sound system that they used at 
various remote broadcasts and other events that required a PA system. For some 
reason, the Chief Engineer had chosen good old fashioned AC Plugs and modified 
extension cords as the interconnects. 

The results were eminently predictable. The CE received a phone call from an 
intern who was working an event. It seems that every one of the loudspeakers 
had the same fault...he'd plug it in, briefly hear a very loud hum, and then 
the speaker would belch black smoke. As I recall, he did that with 4 600 dollar 
loudspeakers before bothering to call anyone. 

Now, who is responsible? The CE or the intern? Or both?

73,

Mike
NM7X
 

------------------------------


Date: Tue, 28 Mar 2006 09:38:18 -0600
From: "Larry Menzel" <retire@means.net>
Subject: Re: [TenTec] Orion Aux Audio output (explained)
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>

Yes, I must admit to several "gozinta" errors while getting to know my 
Orions.  None fatal, however, thus far.

RANT ON:

But you know, as I look at my amplifiers, my oscilloscope, my audio gear, my 
sig-gen, all have common ports for many functions, any one of which, 
misaligned, will yield faulty results.  Let's put any blame for mis-plugged 
plugs directly where it belongs: On the Operator!

Wouldn't it be nice, a kinda kindergarten thing, to have every port color 
coded, and different shaped so we can be protected from oursleves, huh? 
But, guys, were big boys and girls now, and we should be aware enough to 
make SURE the plug is in the right hole before proceeding.  A quick check, 
even if it's with a mirror if you can't get to the back of the rig, should 
be SOP when interconnecting devices.  Let's not blame the tools, eh?

This is a serious radio for serious applications and operators.  It's not a 
toy with non-functional or multipurpose plugs. WE get to decide what we want 
the radio to do, and we have to be able to figure that out AND take 
responsibility for our own errors in judgement or execution.

No offense, guys, but we got what we paid for.  I love the phase, Bob, 
"performance outweighs warts" if you want to call them that.

RANT OFF:

Larry, N0XB

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>