Hmm, I'm also running 2.056, and ever since the first 2.xx release, I
noticed that the audio line out from the Orion's rear connector to my HAL
DXP38 dropped significantly from the 1.372 levels. I had to boost the
TNC's gain, and it's still an inadequate level. It does not vary based
on the volume control of the RX. As far as I can tell, it appears to be
fixed. TT confirmed that gain had been decreased, but they didn't
indicate if that was intentional or not.
73, Duane
On Tue, 28 Mar 2006 01:20:54 +0000 "Barry Gross" <barry.n1eu@gmail.com>
writes:
> On my v2.056 Orion, the aux I/O "line" outputs definitely vary
> (almost
> linearly) with the main/sub af controls.
>
> 73,
> Barry N1EU
>
> On 3/28/06, Larry Menzel <retire@means.net> wrote:
> >
> > Hi, Buck,
> >
> > Well, I"m running RTTY with 2.056, with no problem, using the AUX
> I/O. I
> > set the volume to the program with the volume control for the
> soundcard.
> > The front control has no function on the I/O. Are you sure you
> have the
> > TX
> > Audio Source in the SSB menu set to AUX and not MIC or BOTH? Then
> pull up
> > in Windows START>All Programs>Accessories>Entertainment>Volume
> Control and
> > make sure your LINE IN is enabled, or easier yet just click on the
> volume
> > control in the lower right of your monitor. If you're hooked up
> > correctly,
> > LINE-IN will control the volume to the soundcard from the AUX OUT
> plug on
> > the radio.
> >
> > It is possible that you're simply using the sound from the speaker
> through
> > your microphone to drive the software, because the TX Audio Source
> is set
> > to
> > mic or both.
> >
> > Hope this helps...or call me at 952 212 2664
> >
> > Larry, N0XB
> >
> >
> > ----- Original Message -----
> > From: <K4IA@aol.com>
> > To: <tentec@contesting.com>
> > Cc: <ditsnbits@tentec.com>
> > Sent: Sunday, March 26, 2006 11:27 PM
> > Subject: [TenTec] Orion Aux Audio output
> >
> >
> > >I have been trying to get back into digital modes and notice that
> the
> > audio
> > > output from the AUX I/O connector pin 4 seems to depend on the
> volume
> > > control
> > > instead of being a line out as described in the manual and as
> it
> > operated
> > > prior to ver 2.
> > >
> > > This is maddening because it means you have to turn up the
> volume and
> > > listen
> > > to the warbling. Before you could turn down the volume and just
> watch
> > > the
> > > screen.
> > >
> > > Anyone else notice this?
> > >
> > > K4ia "Buck"
> > > Fredericksburg, Virginia USA
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> > >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
--------------------------------------
Duane Calvin, AC5AA
Austin, Texas
http://home.austin.rr.com/ac5aa
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|