Re: [TenTec] yv5mbx - Orion operation issues

["Toby Pennington" <toby423@earthlink.net>]

Javier,  Another thing that comes to my mind is that if you are doing cw on 
160 and 80 and you are using the filters manually by the menu, and then you 
try to go to ssb, you may be forgetting to change the roofing filter setting 
to a wider  setting to accomodate the wider ssb signals.  I have done this 
often and then wonder whey the ssb signals sound so bad.

Again, the best thing for a beginner is to set the filters on AUTO in the 
menu. That way you will not be confused as much.

As far as startup time, I will check it tomorrow morning and see how long it 
takes from a cold start.    Toby   W4CAK


----- Original Message ----- 
From: "Martin AA6E" <msembx-aa6e@yahoo.com>
To: "Javier Remoto" <jlopez@plasticosomega.com>; <msembx-aa6e@yahoo.com>; 
<tentec@contesting.com>
Sent: Saturday, January 15, 2005 1:09 PM
Subject: Re: [TenTec] yv5mbx - Orion operation issues


> Javier,
>
> Your problem with a long start-up -- I wonder if your power supply is
> giving proper output.  It might be good to measure the voltage and be
> sure it comes up to 13.8 volts (with the Orion attached) when you have
> a "cold start".
>
> 73, Martin AA6E
>
> --- Javier Remoto <jlopez@plasticosomega.com> wrote:
>
> > Hello Martin,
> >
> > I agree with you and what you said abt the lack of technical
> > knowledge apply to me but basically because I had not found further
> > reference condensed in a book.
> >
> > I define myself as contester but all my knowledge is based upon the
> > experiences shared trough Internet lists and trial & error.
> >
> > Good Shot!!!!
> >
> > PD: Regarding the start-up, if the radio had been unused for a day,
> > takes abt 30 secs to appear SYSTEM LOADING and another 30 for full
> > start-up.
> >
> > But after being turned on for minutes, if I turned off and then on
> > takes abt 10 secs too!!!
> >
> > I will made a total reset and see what could be happening.
> >
> >
> > 73's de Javier
> > ----- Original Message ----- 
> > From: "Martin AA6E" <msembx-aa6e@yahoo.com>
> > To: "yv5mbx" <yv5mbx@arrl.net>; <tentec@contesting.com>
> > Sent: Saturday, January 15, 2005 12:59 PM
> > Subject: Re: [TenTec] yv5mbx - Orion operation issues
> >
> >
> > > My Orion (v 1.372 firmware) takes about 12 seconds to come to life.
> > It
> > > _seems_ like a minute! In the future, maybe TT can play some music
> > or
> > > show some exotic DX photos while the radio boots up.
> > >
> > > [Javier - I don't know if the following applies to you! I don't
> > know
> > > your background in radio.]
> > >
> > > More seriously, there is a need for a "tutorial" that will help a
> > new
> > > ham (at a basic technical level) to get the most out of a high
> > > performance rig.  The TenTec Orion manual (now being revised) will
> > > probably never do that job.  It is more a reference manual.
> > >
> > > [Many people will say that Orion is "too much radio" for beginners.
> >
> > > But is that really true, or do we need better user training
> > material?]
> > >
> > > Does anyone know of an existing book that explains SSB and CW
> > tuning,
> > > PBT, AGC, modulation, specifications, etc.?  I.e., how to
> > intelligently
> > > operate your new "appliance"?  Info is scattered through the
> > Internet,
> > > ARRL pubs, and vendors' manuals, but not in one place that I've
> > found.
> > >
> > > 73, Martin AA6E
> > >
> > > --- yv5mbx <yv5mbx@arrl.net> wrote:
> > >
> > > > Hi,
> > > >
> > > > I will try to pinpoint the situation and also will post again on
> > the
> > > > list,
> > > > your ideas will be apreciatted (Maybe a book to be read)
> > > >
> > > > 1.- It takes almost a minute to load the software at radio
> > startup,
> > > > is
> > > > this  normal???
> > > > ...
> > >
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec