Boy my Corsair II manual shows a whole different PTO than my Omni-D manual
does.
Omni D PTO is 80278 with 4 output pins
Corsair II PTO is 81038 with 5 output pins one of which is an enable line
that the Omni does not have. One of the 5 pins is also a Shift line. In the
drwaing of the interconect/block diagram of the radio the pto number is
81036 which I hope is a typo and they really meant 81038.
So from what the manuals say they are significantly different and would
guess could not be swapped easily. Dunno, I have not taken the Corsair II
apart to verify this however.
Steve
----- Original Message -----
From: "Mike Hyder --N4NT--" <N4NT_Mike.Hyder@charter.net>
To: <tentec@contesting.com>
Sent: Wednesday, August 27, 2003 4:28 PM
Subject: Re: [TenTec] PTO transplant!
> I suppose I stand corrected?
>
> Mike
>
> ----- Original Message -----
> From: "N4PY" <n4py@qvssoftware.com>
> To: <tentec@contesting.com>
> Sent: Wednesday, August 27, 2003 2:47 PM
> Subject: Re: [TenTec] PTO transplant!
>
>
> > The only PTO that worked in an opposite direction was the 580 delta
PTO.
> > The Omni A/D and Corsairs all had the same PTO.
> >
> > Carl Moreschi N4PY
> >
> > ----- Original Message -----
> > From: "Mike Hyder --N4NT--" <N4NT_Mike.Hyder@charter.net>
> > To: <tentec@contesting.com>
> > Sent: Wednesday, August 27, 2003 2:08 PM
> > Subject: Re: [TenTec] PTO transplant!
> >
> >
> > > The VFO's work opposite from each other. The threads inside that make
> the
> > > slug move are clockwise in one and counter-clockwise in the other.
> > >
> > > Other than that, I'm not sure of any difference between the PTO's
> > > themselves. If you speak of the external PTO's, get the right one and
> > don't
> > > try to kluge the wrong one into working.
> > >
> > > 73, Mike N4NT
> > >
> > > ----- Original Message -----
> > > From: "Don Rasmussen" <wb8yqj@yahoo.com>
> > > To: <tentec@contesting.com>
> > > Sent: Wednesday, August 27, 2003 12:07 PM
> > > Subject: [TenTec] PTO transplant!
> > >
> > >
> > > > Hi Guys,
> > > >
> > > > Can anyone comment on the interchangability of the
> > > > original OMNI A/D PTO in the Corsair I or II?
> > > >
> > > > I am wondering what might be involved in a
> > > > "transplant".
> > > >
> > > > Anyone have any experience with doing this or comments
> > > > from looking at the shemos?
> > > >
> > > > Both PTOs have 4 wire hookups on the outside of the
> > > > box and it appears from looking at the shemos that
> > > > even though the parts tags are different, the parts
> > > > values and connections are the same or very similar.
> > > >
> > > > Any help or comments appreciated!
> > > >
> > > > 73,
> > > > Don Rasmussen WB8YQJ
> > > > Carlsbad, Ca.
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|