NA-User
[Top] [All Lists]

[NA-User] 2 radios - 1 COM port

To: <na-user@contesting.com>
Subject: [NA-User] 2 radios - 1 COM port
From: wx3m@comcast.net (wx3m@comcast.net)
Date: Wed, 13 Mar 2002 21:22:23 -0500
I understand that the CI-V interface is designed to handle several radios
and will not get confused, but what about NA?

If this is the case, how do I properly assign COM ports? In the CONFIG.EXE
utility, under Serial Port Configuration, there is no provision for making
any one COM port talk to more than one device.

Has anybody else tried this? Succeeded?

Don

Don Chisholm
dchishol@oakland.edu
http://www.oakland.edu/~dchishol/
"I didn't do it.  Nobody saw me.  You can't prove anything." - Bart Simpson

----- Original Message -----
From: Carl - WC4H <wc4h@itis.net>
To: <wx3m@comcast.net>; nauser <na-user@contesting.com>
Sent: Wednesday, March 13, 2002 8:58 PM
Subject: Re: [NA-User] 2 radios - 1 COM port


> The ICOM CI-V interface does not get confused.  It is designed to handle
up
> to 4 radios with 1 COM port.  Each Icom radio uses a different memory
> address.  That is how the interface keeps track of it.  Set each radio to
> it's default address and you should be able to use it.
>
> 73
> Carl
>
> ----- Original Message -----
> From: <wx3m@comcast.net>
> To: <na-user@contesting.com>
> Sent: Wednesday, March 13, 2002 7:24 PM
> Subject: [NA-User] 2 radios - 1 COM port
>
>
> > I have recently (yesterday) acquired a second IC-765. This came with the
> > CI-V interface.
> >
> > I have used my current IC-765 with NA using a homebrew interface. As
they
> > sit right now, RIG-1 is on COM-3 and RIG-2 is on COM-4. All is well and
> > communicating happily . . .
> >
> > I would like to combine the communications to both radios into one COM
> port,
> > (so I can do SO2R from a laptop). The Icom (and the homebrew) computer
> > interfaces allow you to use several radios on one interface.
> >
> > How do I do this?
> >
> > I assume that if I have both radios hooked to the interface on COM X,
and
> NA
> > configured to RIG-1=IC-765 and RIG-2=IC-765, NA and the interface will
not
> > know which radio is which and become confused.
> >
> > I assume I will have to change the address (HEX value/assignment) for
one
> of
> > the radios. If I leave RIG-1 the way it is, and set RIG-2 to, say, an
> > IC-781, and change the radio 2 to communicate like an IC-781, can NA
talk
> to
> > both radios on the same COM port?
> >
> > Don WX3M
> >
> > Don Chisholm
> > dchishol@oakland.edu
> > http://www.oakland.edu/~dchishol/
> > "I didn't do it.  Nobody saw me.  You can't prove anything." - Bart
> Simpson
> >
> > _______________________________________________
> > NA-User mailing list
> > NA-User@contesting.com
> > http://lists.contesting.com/mailman/listinfo/na-user
> >
>
> _______________________________________________
> NA-User mailing list
> NA-User@contesting.com
> http://lists.contesting.com/mailman/listinfo/na-user


<Prev in Thread] Current Thread [Next in Thread>