Also another point I would like to make, look at the FCC cert for the
Zcom card (Demarc) which is at .234 watts (234mW):
https://gullfoss2.fcc.gov/cgi-bin/ws.exe/prod/oet/forms/misc/Grant_Form.
hts?application_id=803728&mode=COPY&fcc_id=M4Y-0325H
Vs
Seano cards which are at .178 watts (178mW)
https://gullfoss2.fcc.gov/prod/oet/cf/tcb/Tcb731GrantForm.cfm?applicatio
n_id=311157&mode=COPY&fcc_id=NI3-2511CD-PLUS3
This is a different of 56mW!!! Again just pointing out these two cards
are very different.
Sincerely, Tony Morella
Demarc Technology Group, A Wireless Solution Provider
Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202
http://www.demarctech.com
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
> [mailto:karlnet-bounces@WISPNotes.com] On Behalf Of Tony Morella
> Sent: Saturday, March 29, 2003 12:29 AM
> To: 'Karlnet Mailing List'
> Subject: RE: [Karlnet] WPBASE+ with SENAO 200mw radio cards
>
>
> Caleb
>
> Have you done side by side testing with both cards? Look at
> the modulated RF signal on an SA? Watch the signal output on
> the cards over time? Test for RX levels changes, over time?
> Look at the internal chipsets and manufacturing processes
> used to make the cards?? Test in outdoor weather conditions??
>
> FYI we have tested and continue to test the Seano cards, this
> is compiled info on the testing:
>
> CH 1 2 3 4 5 6 7
> 8 9 10 11 12 13 14
> Turn on 24.5 24.5 24.3 24 23.9 23.7 23.5
> 23.5 23.4 23.2 23.1 23.1 23 20
> At 10 Min. 18.1 18.2 18.3 18.4 18.7 19 19.1
> 19.2 19.3 19.3 19.4 19.4 19.5 16.5
>
> Using the Internsel test info:
> http://www.demarctech.com/techsupport/rw-wireless-cards-suppor
> t/wlan-rec
> eiver-test.pdf
>
> Sensitivity @ 11Mbps,FER<8%
> Ch1 Ch7 Ch14
> -83dB -83dB -83dB
>
> The Seano cards and Zcom cards are VERY different in there
> design, for one Seano uses a low cost 2nd stage that max
> out, where the Zcom cards uses a 500mW 2nd stage! The reason
> the Zcom cards cost more is simply because they use better
> quality components and have a better design which is the
> reason Demarc OEMs these cards. All the info is there to run
> the test your-self.
>
> Sincerely, Tony Morella
> Demarc Technology Group, A Wireless Solution Provider
> Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202
> http://www.demarctech.com
>
>
>
> > -----Original Message-----
> > From: karlnet-bounces@WISPNotes.com
> > [mailto:karlnet-bounces@WISPNotes.com] On Behalf Of Caleb Carroll
> > Sent: Friday, March 28, 2003 4:27 PM
> > To: Karlnet Mailing List
> > Subject: RE: [Karlnet] WPBASE+ with SENAO 200mw radio cards
> >
> >
> > These cards are all pretty much identical and Zcomax cards
> > are just expensive. We have a shitload of EnGenius cards
> > (re-branded Senao) and they've been working fine for months
> > (as long as you're using TurboCell and not 802.11b of course).
> >
> > We're using the EnGenius cards with RG-1100's and AP-1000's
> > though, so I can't help Don with this problem but somehow I
> > doubt that the problem is with the Senao cards.
> >
> > *********** REPLY SEPARATOR ***********
> >
> > On 2003-Mar-28 at 10:14 AM Charles Chia Sheng Wu wrote:
> >
> > >Senao cards are crap, use the Zcomax cards
> > >
> > >-Charles
> > >
> > >-----Original Message-----
> > >From: karlnet-bounces@WISPNotes.com
> > >[mailto:karlnet-bounces@WISPNotes.com]On Behalf Of Don Starnes
> > >Sent: Friday, March 28, 2003 9:57 AM
> > >To: Karlnet
> > >Subject: [Karlnet] WPBASE+ with SENAO 200mw radio cards
> > >
> > >
> > >Hello everyone,
> > >
> > >I am having a hard time trying to get the new WPBASE+ to work with
> > >SENAO 200mw (Intersil 2.5) or 100mw (Intersil 2.0) radio
> cards. The
> > >board recognizes the radios and will let you program them
> as usual.
> > >The problem seems to occur after they have been in service
> for a few
> > >hours. I get very erratic behavior from the boards such as:
> > 1. Second
> > >radio stops working 2. Second radio disappears
> > >3. Port shows empty PCMCIA when I know there is a card in it.
> > >
> > >I know everyone's setup can be different. We are using 12v
> > 10a power
> > >supplies to power these boards. We have version 4.43a bin
> > file on the
> > >radios.
> > >
> > >Any suggestions?
> > >
> > >Thank You,
> > >
> > >Don
> > >
> > >
> > >_______________________________________________
> > >Karlnet mailing list
> > >Karlnet@WISPNotes.com
> > >http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> > >_______________________________________________
> > >Karlnet mailing list
> > >Karlnet@WISPNotes.com
> > >http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> >
> >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/ka> rlnet
> >
> >
>
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/ka> rlnet
>
>
|