Do you have Enable Bridging checked along with Incoming & Outgoing NAT???
If so you will be bridging your private IPs. And it might appear to be a
leaky NAT...
Nate
-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On
Behalf Of Dan Metcalf
Sent: Tuesday, September 17, 2002 7:44 AM
To: karlnet@WISPNotes.com
Subject: RE: [Karlnet] NAT SETTING - INHIBIT NAT FROM INTERFACE ? what
does it do?
This option is under outgoing nat setup, we are having a problem with
v4.02 and NAT leaking through. I'm wondering if this setting has
anything to do with it?
Does anybody know what this setting does?
Dan Metcalf
Wireless Broadband Systems
http://www.wbsysnet.com/
877-685-0578
dan.metcalf@wbsysnet.com
> -----Original Message-----
> From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
On
> Behalf Of nate
> Sent: Monday, September 16, 2002 9:48 PM
> To: karlnet@WISPNotes.com
> Subject: Re: [Karlnet] WavePoint - II E ???
>
> I will give it a try.
> I wouldn't think it would be that picky...
> But I did try lots of different ways and timing when i was trying to
get
> it
> into base boot mode.
>
> I will give this one a try as well.
>
> Nate
>
>
> > Hello Nate,
> >
> > The WPII are picky about the order and timing of pressing the reset
> > and reload buttons.
> >
> > Press the reset and when the "PC card B" LED turn orange, quite
> > quick, rrelease the reset and press the reload untill the power led
> > is oraange.
> >
> > good luck
> >
> > Rod
> >
> > Monday, September 16, 2002, 6:17:43 PM, you wrote:
> >
> > NM> Has anyone else had any problems flashing the WP-II E??
> > NM> I just tried to flash 2 of these and they both act the same
way....
> >
> > NM> You can read them with the configev program.
> > NM> Get your license, Open config file, select the .bin file.
> > NM> Scan for the radio. Change the IP of the WPIIE to a IP in my
subnet.
> > NM> Upload the software.
> >
> > NM> Let the AP reboot and then your hosed...
> > NM> You can never scan it and you never get another network
> > connection to it...
> >
> > NM> I tried doing a forced reload as described in the pdf file and I
> > can't ever NM> get it into base boot mode... The power led always
> > goes to green. And no NM> network connection.
> >
> > NM> Can someone shed some light on this problem?
> >
> > NM> TIA
> >
> > NM> Nate
> >
> > NM> _______________________________________________
> > NM> Karlnet mailing list
> > NM> Karlnet@WISPNotes.com
> > NM> http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> > --
> > Best regards,
> > A. mailto:things@mail.chiriqui.com
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>
> --
> Open WebMail Project (http://openwebmail.org)
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> ---
> [This E-mail scanned for viruses by Declude Virus]
---
[This E-mail scanned for viruses by Declude Virus]
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
|