CT-User
[Top] [All Lists]

Re: [ct-user] CT-MFJ 434

To: "Kersus, Gerald J (Gerry), ALABS" <kersus@att.com>,"Bob Schreibmaier" <k3ph@ptd.net>, <ct-user@contesting.com>
Subject: Re: [ct-user] CT-MFJ 434
From: Ed Parish K1EP <k1ep@arrl.net>
Reply-to: k1ep@arrl.net
Date: Fri, 04 Mar 2005 09:46:52 -0500
List-post: <mailto:ct-user@contesting.com>
At 3/4/2005 07:13 AM, Kersus, Gerald J (Gerry), ALABS wrote:
>Bob,
>I happen to run two PCs:  one running CT Version 10 on DOS and the other
>running CTWin Version 10 on Windows 98.  I also use CVB with a homebrew
>interface that uses the LPT output for keying the radio.  With Version
>10, LPT doesn't work with either the DOS or Win98 PC!!  Going back to CT
>Version 9 works just fine.

As someone stated, you may have to change the BIOS to set the correct type of 
parallel port.  Also, I noted that the LPT port pinout on the k1ea website says 
that pin 11 is ground.  I looked at it the other day and it wasn't.  Maybe one 
version of the software sets or resets that bit to ground and one doesn't.  If 
your interface uses pin 11, you might want to switch to some other ground pin, 
such as 18.


>Gerry, W1GD 
>
>-----Original Message-----
>From: ct-user-bounces@contesting.com
>[mailto:ct-user-bounces@contesting.com] On Behalf Of Bob Schreibmaier
>Sent: Thursday, March 03, 2005 10:41 PM
>To: ct-user@contesting.com
>Subject: [ct-user] CT-MFJ 434
>
>One caution, make sure you're using CT-DOS.
>CTWin doesn't appear to support voice keying
>from the LPT port.
>
> >What do you mean by this?  Do you want to key it from CT?
> >
> >There is a schematic on page 14 of the manual.  Setup CT to use one of
>
>the LPT ports, making sure that it is configured properly (like ECP). 
>Pins 3,4,5, &6 correspond to messages F1, F2, F3, F4.  Output of the 
>parallel port is 5V positive going.  Ground is 11.  One problem you will
>
>have to solve is that the STOP function in the 434 is a separate button.
>
>  On the DVP card it is ESC.   You will find that you will only get 3 
>messages out of this setup, having to probably dedicate one F button to 
>STOP.
> >
> >At 3/3/2005 07:14 PM, stanley elkins wrote:
> >>I would like to use a MFJ 434 Voice keyer with CT.
> >>Has anyone used this setup and how is it done
> >>Any help would be appreciated
>
>-- 
>+----------------------------------------------+
>| Bob Schreibmaier K3PH | E-mail: k3ph@ptd.net |
>| Kresgeville, PA 18333 | http://www.dxis.org  |
>+----------------------------------------------+
>
>_______________________________________________
>CT-User mailing list
>CT-User@contesting.com
>http://lists.contesting.com/mailman/listinfo/ct-user
>CT on the web:  http://www.k1ea.com/
>
>
>
>_______________________________________________
>CT-User mailing list
>CT-User@contesting.com
>http://lists.contesting.com/mailman/listinfo/ct-user
>CT on the web:  http://www.k1ea.com/

_______________________________________________
CT-User mailing list
CT-User@contesting.com
http://lists.contesting.com/mailman/listinfo/ct-user
CT on the web:  http://www.k1ea.com/

<Prev in Thread] Current Thread [Next in Thread>