Amps
[Top] [All Lists]

Re: [Amps] LK550 ALO/Meter board interconnect - anyone know what the man

To: amps@contesting.com, gudguyham@aol.com
Subject: Re: [Amps] LK550 ALO/Meter board interconnect - anyone know what the manufacturer or part/type of the two 6-pin nylon connectors that mate with J1/J2 on the ALO/Meter board?
From: wb0gaz via Amps <amps@contesting.com>
Reply-to: wb0gaz@yahoo.com
Date: Wed, 1 Nov 2023 22:33:22 +0000 (UTC)
List-post: <mailto:amps@contesting.com>
 
Thanks! That is consistent with my thought - with 3-500Z tubes, there's nothing 
to be gained as long as the op pays attention...

If I can identify the PCB-end connectors in use, that will reduce the hassle of 
pulling them, but your comment adds fodder to the idea that the board wouldn't 
likely be of future use anyway...

     On Wednesday, November 1, 2023 at 04:26:44 PM MDT, gudguyham@aol.com 
<gudguyham@aol.com> wrote:  
 
 Dave, the ALO boards on these amps are for the most part worthless.  They 
don’t trip on the important factors anyway.  When they go bad I usually just 
bypass them.  Not worth the effort to repair them unless it’s something 
obvious.  The LK550 HD as 3 3-500 tubes.  As long as your meters are working 
properly you don’t need any trip circuits.  With the LK800 amps the ALO board 
has a timer on it to hold off RF until the cathodes warm up, there it’s a must! 
 But even still I don’t believe it trips on grid overload.  If you are 
concerned about real protection most tubes benefit from a simple grid trip 
circuit which is a lot less complicated than the ALO board.  Some ALO boards do 
have grid shunt series resistors that will occasionally open up with tube arcs. 
 They usually can be seen as bad when inspected closely. 


Sent from the all new AOL app for iOS


On Wednesday, November 1, 2023, 5:29 PM, wb0gaz via Amps <amps@contesting.com> 
wrote:

 Thanks (Dave) for insight on the panel meters.

Arriving to the point (on LK550) that the ALO/Meter board is suspect - either 
was damaged or caused damage in it's prior life. Several traces handling 12V 
path were badly overheated, one to the point of destruction, and the board 
(with a couple of previously added jumpers to bypass two of the smoked traces) 
is still dragging the 12V DC control power supply (simple half-wave rectified 
off the low voltage transformer) down to near zero when amplifier is enabled 
(XMIT on the XMIT/STBY switch.)

Now intend to delete ALO/Meter and rewire as if it were a LK500 or other model 
without ALO/Meter (hence why I wanted to understand the nature of the two panel 
meters.)

Next step is to find pair of nylon 6-pin connectors (equal to what are 
currently on the ALO/Meter board); they are physically polarized and a search 
through digikey hasn't found anything equivalent so far. Although could remove 
the connectors from the (suspect) ALO/Meter board, would rather set it aside 
as-is for now and source replacement connectors (on the PCB, the two connector 
housing are female, and the (6) pins are male.) My supply of pins doesn't 
include any that are the same dimension as the one used on the PCB (else I'd 
just stuff equivalent pins into the needed positions on the end-of-wire 
connectors and call it a day.)

Thanks again for the hand-holding through this saga!

Dave

  
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps



  
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
<Prev in Thread] Current Thread [Next in Thread>