Leigh,
It would be too difficult to diagnose why the user had both tubes go out in
his commercial amp. Did he say it was an OM Power unit. I think he was in
Italy and should contact OM Power to figure out happened. He could return
it to them, maybe he did. Or perhaps he had one of those LA4000 that also
use FU728F tubes.
Jay Terleski
Array Solutions
214 954 7140
On Thu, Sep 19, 2019 at 10:36 PM Leigh Turner <invertech@frontierisp.net.au>
wrote:
>
> All good comments here Jay. But you omitted to speak to the subject line
> and
> offer an opinion on the likely reason why the pair of FU728 tubes both
> failed with grid to cathode shorts?
>
> What did the owner do wrong, and what teachings should other owners of the
> OM4000 amplifier take note of when tuning up for low power or AM modulation
> and avoiding an expensive tube replacement exercise?
>
> 73
>
> Leigh
> VK5KLT
>
> -----Original Message-----
> From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Jay Terleski
> Sent: Friday, 20 September 2019 2:00 AM
> To: amps@contesting.com
> Subject: Re: [Amps] Amps Digest, Vol 201, Issue 12
>
> I get a kick out of this tube thread. But let me try to add some sanity to
> the weirdness of it.
>
> There is no way we, Array Solutions, told anyone to run the amp at or near
> the high power limit to avoid cooking the tube. Just tune it normally and
> keep the screen current at zero ma. Your gonna be OK at lower power
> output.
>
> Also with these tubes you want to make sure your filaments are very close
> to 9V. So watch the mains voltage. Many parts of the country are getting
> well over 247V AC mains and that means your filaments may be running high.
>
> Best wishes to the group.
> Jay, WX0B
>
> Jay Terleski
> Array Solutions
> 214 954 7140
>
>
> On Thu, Sep 19, 2019 at 11:00 AM <amps-request@contesting.com> wrote:
>
> >
> > Today's Topics:
> >
> > 1. Re: Failure of a pair of FU728F (Greg Wasik)
> > 2. Re: Failure of a pair of FU728F (Joe Subich, W4TV)
> > 3. Re: Failure of a pair of FU728F (dj7ww@t-online.de)
> > 4. Re: Failure of a pair of FU728F (Leigh Turner)
> >
> > ----------------------------------------------------------------------
> >
> > Message: 1
> > Date: Wed, 18 Sep 2019 14:13:39 -0400
> > From: Greg Wasik <gwasik@gmail.com>
> > To: "Roger (K8RI)" <k8ri@rogerhalstead.com>
> > Cc: amps@contesting.com
> > Subject: Re: [Amps] Failure of a pair of FU728F
> >
> > Guessing that if you wanted to run legal limit AM with the OM4000 you
> would
> > want to avoid any long pauses in your modulation so that the average
> power
> > is at least 1KW. A dead key would be deadly...
> >
> > Greg
> > K1YW
> >
> > On Wed, Sep 18, 2019, 4:22 AM Roger (K8RI) <k8ri@rogerhalstead.com>
> wrote:
> >
> > > On 9/15/2019 4:39 PM, Paul Christensen wrote:
> > > >> "A friend of mine ruined the finals in his OM4000 by running the amp
> at
> > low power. Array solutions told him the amp is designed to be run full
> power or
> > very close to it.
> > 73 de Mike W9OJ"
> > >
> > > Which is a bit confusing. As I understand as the amps are sold they
> > > require a lot of drive for the legal limit as there is a gain
> limitation
> > > requirement. The input circuit must be modified to get the amp's full
> > > capability
> > >
> > > HOWEVER the FU728F requires about 60 to 70% of full power before the
> > > screen current flows in the proper direction. Although not large there
> > > is a reverse screen current area. With the proper voltages and drive a
> > > single FU728F can hit 2500 PEP output, or 2000W carrier in the Emtron
> > > DX-2sp
> > >
> > > 73 Roger (K8RI)
> > >
> > > > I nearly ruined the FU-728F in my OM Power 2000A+ because the cathode
> > was running cold. My QRZ page describes some details. Bottom line:
> don't
> > assume the power transformer tap (i.e., 250V, 240V, 230V) matches the
> > utility line voltage. Choose the tap that results in 9.0 VAC on the
> > filament, exactly as to spec. That will result in an adequately heated
> > cathode.
> > > >
> > > > My AC mains runs at 255V. The remote site is the only subscriber on
> > the drop. I initially set the amp's tap to 250V but the filament was
> > starved as the high tap resulted in 8.0-8.5V. Filament voltage dropped
> even
> > further when the amp attempted to make full power. The first clue to all
> this
> > occurred about six months after installation. I noticed a fast 50% drop
> in
> > output power when keying the amp. When keying the amp, it would
> > initially produce full power, then quickly drop. At first, I was going
> to
> blame
> > component heating in the RF deck but the root cause was much simpler.
> >
> > Another recent issue with the amp was step-start. The step resistor
> > blew before its fuse could open. The wirewound resistor's winding could
> > only take so many surge events before opening. I ended up stacking two
> > identical resistors at 2X the value in parallel to equally divide the
> surge
> > current between them.
> >
> > Paul, W9AC
> > > >
> > > > _______________________________________________
> > > > Amps mailing list
> > > > Amps@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/amps
> > > --
> > > Roger (K8RI)
> > >
> > ------------------------------
> >
> > Message: 2
> > Date: Wed, 18 Sep 2019 17:13:41 -0400
> > From: "Joe Subich, W4TV" <lists@subich.com>
> > To: amps@contesting.com
> > Subject: Re: [Amps] Failure of a pair of FU728F
> > Message-ID: <02cd5628-ae76-411e-6ac9-29fe2338c40f@subich.com>
> > Content-Type: text/plain; charset=utf-8; format=flowed
> >
> > "Legal limit" AM is 375 W of carrier -> 1500 W PEP. Whether the OM4000
> > can be tuned properly for that operating condition is another story.
> >
> > 73,
> >
> > ... Joe, W4TV
> >
> >
> > On 2019-09-18 2:13 PM, Greg Wasik wrote:
> > > Guessing that if you wanted to run legal limit AM with the OM4000 you
> > would want to avoid any long pauses in your modulation so that the
> average
> > power is at least 1KW. A dead key would be deadly...
> > >
> > > Greg
> > > K1YW
> > >
> > ------------------------------
> >
> > Message: 3
> > Date: Thu, 19 Sep 2019 01:18:01 +0200
> > From: <dj7ww@t-online.de>
> > To: <amps@contesting.com>
> > Subject: Re: [Amps] Failure of a pair of FU728F
> > Message-ID: <AF52D62FEE5247E782E83EF1C142AFAF@DJ7WW2>
> > Content-Type: text/plain; charset="us-ascii"
> >
> > Yes, the pi net design values for 4KW PEP are quite different to 1.5KW.
> > If designed for 4k, circuit Q will be almost doubled for 1.5k.
> > And I doubt it can be tuned on 10m with that high tube impedance.
> >
> > 73
> > Peter
> >
> >
> > -----Original Message-----
> > From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Joe Subich,
> > W4TV
> > Sent: Mittwoch, 18. September 2019 23:14
> > To: amps@contesting.com
> > Subject: Re: [Amps] Failure of a pair of FU728F
> >
> > "Legal limit" AM is 375 W of carrier -> 1500 W PEP. Whether the OM4000
> > can be tuned properly for that operating condition is another story.
> >
> > 73,
> >
> > ... Joe, W4TV
> >
> >
> > On 2019-09-18 2:13 PM, Greg Wasik wrote:
> > > Guessing that if you wanted to run legal limit AM with the OM4000 you
> > would want to avoid any long pauses in your modulation so that the
> average
> > power is at least 1KW. A dead key would be deadly...
> > >
> > > Greg
> > > K1YW
> > >
> > _______________________________________________
> > Amps mailing list
> > Amps@contesting.com
> > http://lists.contesting.com/mailman/listinfo/amps
> >
> > ------------------------------
> >
> > Message: 4
> > Date: Thu, 19 Sep 2019 14:02:42 +0930
> > From: "Leigh Turner" <invertech@frontierisp.net.au>
> > To: <amps@contesting.com>
> > Subject: Re: [Amps] Failure of a pair of FU728F
> >
> > Yeah running a tetrode based muscle amp as a linear for AM is problematic
> > and caution must be exercised in obtaining optimal plate loading and
> choice
> > of plate load line not causing excessive power to be dissipated in the
> > tube....and associated poor efficiency. That internal heating is what
> > likely warped the delicate and closely spaced control grid structure
> > (yielding the tube's high power gain) causing the unfortunate heater
> short
> > and catastrophic failure in BOTH tubes.
> >
> > The OM4000 amp's tank circuit is optimised for running at or near
> > full-tilt....
> >
> > In a Pi or Pi-L tank network one ideally needs a variable tank inductor
> to
> > accommodate proper tuning for widely disparate levels in RF power output.
> >
> > Leigh
> > VK5KLT
> >
> > -----Original Message-----
> > From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Greg Wasik
> > Sent: Thursday, 19 September 2019 3:44 AM
> > To: Roger (K8RI)
> > Cc: amps@contesting.com
> > Subject: Re: [Amps] Failure of a pair of FU728F
> >
> > Guessing that if you wanted to run legal limit AM with the OM4000 you
> would
> > want to avoid any long pauses in your modulation so that the average
> power
> > is at least 1KW. A dead key would be deadly...
> >
> > Greg
> > K1YW
> >
> > On Wed, Sep 18, 2019, 4:22 AM Roger (K8RI) <k8ri@rogerhalstead.com>
> wrote:
> >
> > > On 9/15/2019 4:39 PM, Paul Christensen wrote:
> > > "A friend of mine ruined the finals in his OM4000 by running the amp
> at
> > low power.
> > > Array solutions told him the amp is designed to be run full power or
> very
> > > close to it.
> > >
> > > > 73 de Mike W9OJ"
> > >
> > > Which is a bit confusing. As I understand as the amps are sold they
> > > require a lot of drive for the legal limit as there is a gain
> limitation
> > > requirement. The input circuit must be modified to get the amp's full
> > > capability
> > >
> > > HOWEVER the FU728F requires about 60 to 70% of full power before the
> > > screen current flows in the proper direction. Although not large there
> > > is a reverse screen current area. With the proper voltages and drive a
> > > single FU728F can hit 2500 PEP output, or 2000W carrier in the Emtron
> > > DX-2sp
> > >
> > > 73 Roger (K8RI)
> > >
> > > I nearly ruined the FU-728F in my OM Power 2000A+ because the cathode
> was
> > > running cold. My QRZ page describes some details. Bottom line: don't
> > > assume the power transformer tap (i.e., 250V, 240V, 230V) matches the
> > > utility line voltage. Choose the tap that results in 9.0 VAC on the
> > > filament, exactly as to spec. That will result in an adequately heated
> > > cathode.
> > >
> > > My AC mains runs at 255V. The remote site is the only subscriber on
> the
> > > drop. I initially set the amp's tap to 250V but the filament was
> starved
> > as the high tap resulted in 8.0-8.5V. Filament voltage dropped even
> further
> > > when the amp attempted to make full power. The first clue to all this
> > > occurred about six months after installation. I noticed a fast 50%
> drop
> > in output power when keying the amp. When keying the amp, it would
> > > initially produce full power, then quickly drop. At first, I was going
> > to blame component heating in the RF deck but the root cause was
> > much simpler.
> > >
> > > Another recent issue with the amp was step-start. The step resistor
> blew
> > > before its fuse could open. The wirewound resistor's winding could
> only
> > > take so many surge events before opening. I ended up stacking two
> > > identical resistors at 2X the value in parallel to equally divide the
> > > surge current between them.
> > >
> > > Paul, W9AC
>
>
>
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|