With all the answers from the real experts at hand, I feel safe offering my
2 cents on the topic.
If you suffer from an amplifier (or anything else) blowing fuses, like this
amp is doing, you need to isolate the problem as Jim has recommended. An
alternative way to accomplish that end is to set your amp up with a current
limiting device so that you do not exceed the fuse rating and thus blow the
fuse. You can then turn on the amp and make meter readings to find out
where the voltage drop is. Of course you need to know how to use a meter
properly.
How do you build a current limiter for your amp? Well it is actually dead
simple. Use a light bulb in series with the power lead to the amp. Since
you are running this amp on 120 volts AC, you only need one light bulb. If
you were running 220, you'd need two.
Consider: If you want to limit current to 1/2 amp total, you would use a 60
watt 120 volt common light bulb in series with the power lead. Use bigger
bulbs as necessary to allow increased current flow. Of course finding 100
watt light bulbs these days is problematical but the concept is
straightforward and substitutes can be used.
If you turn on the amp and the bulb goes full bright, then you know you have
a bad short to ground. If you do not have a short, the bulb will barely
glow. In the meantime, running your tests will not result in a trashcan of
blown fuses and you will not be stressing other components.
Long story short, light bulbs in series with the main voltage act as perfect
current limiters. This concept also works with any power feed, circuit
breaker, etc. Put the concept into your toolbox of tricks and gadgets, it
works well.
Mark
wa3jpy
----- Original Message -----
From: "Jim Thomson" <jim.thom@telus.net>
To: <amps@contesting.com>
Sent: Thursday, July 06, 2017 4:42 PM
Subject: [Amps] SB220 step start blows fuses
Date: Thu, 6 Jul 2017 00:07:50 -0600
From: Warren Volz <warren@warrenvolz.com>
To: amps <amps@contesting.com>
Subject: Re: [Amps] SB220 step start blows fuses
<Without tubes and with the HV transformer unplugged, the fan and meter
lights work. In addition, the step-start fuses don?t blow!
<That leads me to suspect the tubes + HV supply. I checked the windings on
the HV transformer to look for shorts:
BLK-YEL = .7 Ohm
BLK-BLKYEL = .6 Ohm
BLKYEL-YEL = 0 Ohm
BLKGRN - BLU = .8 Ohm
BLKGRN - BLKRED = .6 Ohm
BLU - BLKRED = 0 Ohm
Do any of those look off?
Also, would these steps (or something similar) make sense?
1) Re-enable HV supply, power on, if fuses are ok power off and go to step
2
2) Once HV dissipates, add tube 1, if fuses are ok, power off and go to
step 3
3) Assume tube 2 is shorted, else tube 1 is bad
-Warren
### With NOTHING connected to the SEC winding of the plate xfmr, you
should see aprx
9-10 ohms of dc resistance. You could also hook it all back up, then,
with tubes REMOVED
from sockets...OR disconnect the B+ from the top of each tube..... try it
again. If normal B+ appears,
its one or both tubes. You really need to isolate stuff. IF plate
xfmr is good, the trbl could be in the
FW Doubler diodes. IF diodes are ok, it could be the 8 x filter caps,
or eq resistors across each filter cap.
It could be a bad HV interlock assy, it could be the plate choke assy,
it could be anything..including a
internal shorted, or partially shorted plate xfmr. Or any HV inter
connecting wiring between any of the above
components. Or it could be your new step start assy itself.
Jim VE7RF
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|