I'm running 8 core CPUs OCd to 5 GHz. They require water cooling. The
only time the dump a lot pf heat, is either gaming, or serious number
crunching. Few processors run anywhere near their max ratings
otherwise, but they can and do put out their rated heat under certain
conditions. Just like comparing a car engine at idle Vs full throttle.
Typical office applications use very little power.
Most of the big name coolers will handle the power they claim, but with
little to none for excess heat. Some can be a royal PITA to install though.
73
Roger (K8RI)
On 8/31/2016 Wednesday 10:49 AM, Manfred Mornhinweg wrote:
Alex,
I don't know about that, but you have liquid cooled heatsinks for
high power processors capable of taking care of a few hundreds of
watts.
In the PC overclocking scene, a lot of snake oil is being sold. I
would first do a reality check on any CPU cooler rated for several
hundred watts, before using it for a real high power application. The
fact is that PC CPUs normally run at a very much lower power level.
The one in my PC, a dual core CPU running at 2.8GHz, dissipates an
average of barely 10W, and when both cores are loaded to full capacity
it increases to around 20W. There are certainly some CPUs that
dissipate far higher power, but I doubt that anyone comes even
remotely close to the 600 to 1000W that an LDMOSFET in high power ham
service would dissipate.
What you can do is
glue the device on the heatsink using silverr loaded epoxy from
Elecolit or some equivalent.
That glue would need to have excellent electrical conductivity, in
addition to thermal conductivity. After all the LDMOSFET sources
connect only through the heatsink. I much prefer soldering.
> We did dolfder devices to copper
heatsinks .but that requires special heating plates going up to about
240 degrees centigrade, and some eutectic solder, not cheap. Don't
try it with new devices.
With some care and ingenuity, a thick copper or aluminium plate placed
on the kitchen range or a camping stove will do fine. Or a heat gun or
soldering torch can be used to heat the plate. The melting solder will
tell the temperature. Just heat the plate slowly enough, to avoid
thermal overshoot to a dangerous level, after the solder melts.
Is anybody here elegant enough to have his clothes ironed? If so, that
iron can make a suitable hot plate for soldering! Many get just hot
enough for it, when set to the hottest level they have.
But my favorite method for soldering transistors to heat spreaders or
sinks, and to do SMD soldering, is the electric oven in my kitchen. It
easily develops enough heat. I just place the items to be soldered in
the oven, with some paste solder, then switch it on and watch. As soon
as the solder melts, I switch it off. I watch the temperature on my
digital multimeter, which has a temperature range and comes with a
thermocouple that's fine for such temperatures, and easily enters the
oven through the door seal. After switching off, the temperature keeps
increasing for a while, due to the heat accumulated in the heating
elements. With my oven, when I switch off as soon as the solder melts,
the air temperature overshoots to about 220°C, which is fine to
achieve a good solder joint, and is totally safe for LDMOSFETs.
I let it cool slowly, with the oven door closed, until the solder
solidifies, then slightly open the oven door to speed the cooling.
Unless the LDMOSFET is held in place by some other system, it's a good
idea to use two heat-resistant objects to clamp it down by gravity.
Otherwise it tends to float on the solder and move out of place. The
objects I use are simply bent from thick wire, and have three legs:
Two go on the heat spreader, the third on the transistor. That's
enough to keep the transistor in place.
SMD components on a printed circuit board don't need this, because as
long as the PCB is correctly designed, they will self-center on the
pads while the solder is liquid.
And here is an example of eutectic, no-clean solder paste that works
great. This amount is enough for a good number of LDMOSFETS and many
complete SMD boards, and costs under $14:
http://www.digikey.com/product-detail/en/chip-quik-inc/SMD291AX/SMD291AX-ND/1160002
Don't buy larger amounts unless you run a factory! This 5cc syringe
would be enough to last a hobby electronician many years! But shelf
life limits it to only 2 years or so. In fact the data sheet says
less, but 2 years stored in the fridge is realistic. After that it
gets pretty stiff, but can still be used, applying it with a tip
rather than through the syringe needle.
Manfred
========================
Visit my hobby homepage!
http://ludens.cl
========================
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|